A
-
A36 sheet
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
AA6061-T6
Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
-
AA6061-T6
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
AA6061-T6
Experimental investigation on mechanical properties affected by dissimilar friction stir spot welding of aluminum 6061-T6 alloy to copper [Volume 10, Issue 6, 2023, Pages 53-64]
-
ABAQUS
Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
-
ABAQUS
Designing and manufacturing of a heavy equipment rotary table equipped with PLC control [Volume 10, Issue 3, 2023, Pages 43-53]
-
ABAQUS
Analysis of a Crotch corner crack in the shell-nozzle junction of a cylindrical pressure vessel under internal pressure using the J-integral method [(Articles in Press)]
-
Abrasive powders
The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
-
Abrasive Water Jet Machining
Optimization of surface roughness, striation and burr formation during machining of aluminum 2024-T351 with abrasive water jet machining [Volume 7, Issue 10, 2020, Pages 12-25]
-
ABS-Ni composite
Experimental investigation of mechanical and microscopic properties of ABS-Ni composite made by Fused Deposition Modeling (FDM) method [Volume 9, Issue 9, 2022, Pages 10-20]
-
Absorbed Energy
An experimental and numerical study on the low-velocity impact behavior of polymer matrix Kevlar-Basalt hybrid composites [Volume 7, Issue 6, 2020, Pages 44-55]
-
Accumulative compound extrusion
Numerical and experimented study of UFG pure copper with high strength processed by Accumulative compound extrusion (ACE) [Volume 7, Issue 3, 2020, Pages 42-51]
-
Accumulative Roll Bonding
Review on accumulative roll bonding of ultrafine grained and nanostructured sheets [Volume 6, Issue 4, 2019, Pages 37-51]
-
Acoustic Data
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
Acoustic Impedance
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Acoustic transducer
Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
-
Acoustophoretic
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Acrylonitrile butadiene rubber
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Adams
Theoretical and numerical investigation of workpiece jamming in fixture using block and palm case study [Volume 6, Issue 3, 2019, Pages 20-27]
-
Additive Manufacturing
Optimized thermal gradient by changing temperature parameters for laser-assisted additive manufacturing process based on polyamide-12 powder using numerical model [Volume 5, Issue 4, 2018, Pages 26-36]
-
Additive Manufacturing
Topology Optimization Of Structures With Thermal And Mechanical Loading [Volume 7, Issue 12, 2020, Pages 54-63]
-
Additive Manufacturing
Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
-
Additive Manufacturing
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
-
Additive Manufacturing
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Additive Manufacturing
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Additive Manufacturing
Experimental investigation of mechanical and microscopic properties of ABS-Ni composite made by Fused Deposition Modeling (FDM) method [Volume 9, Issue 9, 2022, Pages 10-20]
-
Additive Manufacturing
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Additive Manufacturing
Three-Dimensional Geometry Profile Extraction of Deposits Using Linear Laser Scanning in the Directed Energy Deposition Additive Manufacturing Method [(Articles in Press)]
-
Additive Manufacturing
Investigating the influencing parameters on the surface roughness of polymer parts by Fused Deposition Modeling with respect to laser polishing [(Articles in Press)]
-
Additive Manufacturing
Investigation of Mechanical and Thermal Properties of Continuous Metal Wire Reinforced Samples in Fused Deposition Modeling for Shape Memory Stimulus [(Articles in Press)]
-
Additive Manufacturing
Experimental investigation of the compressive strength of polylactic acid/continuous glass fiber composite material produced with an extrusion-based 3D printer using the simultaneous impregnation system of fibers and polymer [(Articles in Press)]
-
Adhesive Joint
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Advanced high strength steel
Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
-
Advanced High-strength Steel
The effects of Cr addition on the phase transformation, microstructure and
mechanical properties of advanced high-strength steel [Volume 7, Issue 8, 2020, Pages 45-53]
-
Advanced high strength steel (AHSS)
Investigating the microstructure, mechanical properties and hole expansion of advanced high strength steel with the approach of application in the car body [Volume 10, Issue 6, 2023, Pages 16-28]
-
Advanced ore sorting
Design and construction of advanced sorting inorder to chromite segregation [Volume 9, Issue 3, 2022, Pages 11-17]
-
AFM
Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
-
AFM
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Age Hardening
The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
-
Air Cooling
The effects of Cr addition on the phase transformation, microstructure and
mechanical properties of advanced high-strength steel [Volume 7, Issue 8, 2020, Pages 45-53]
-
Air manifold
Fabrication and numerical analysis of glass fiber reinforced composite air manifold under vibration loading [Volume 7, Issue 12, 2020, Pages 64-75]
-
AISI304
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
-
AISI 4130
Effect of Temper and Quench Heat Treatment on Mechanical Properties and Microstructure of AISI 4130 to AISI 4340 Steel Joint with GTAW Process [(Articles in Press)]
-
AISI-4140
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
AISI630 steel, hot turning
Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
-
AISI O1 Cold work Tool Steel
Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
-
Al 2024
Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
-
Al 2024-T351
Optimization of surface roughness, striation and burr formation during machining of aluminum 2024-T351 with abrasive water jet machining [Volume 7, Issue 10, 2020, Pages 12-25]
-
Al2O3 Nano particle
Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
-
Al3105 aluminum
The effect of the die geometry on the joint strength of Al 3105 aluminum sheets joined by the clinching process [Volume 7, Issue 12, 2020, Pages 10-23]
-
Al 356
Experimental and numerical analysis of parameters affecting the mechanical behavior of closed cell aluminum foam in low-speed impact [Volume 9, Issue 12, 2022, Pages 43-53]
-
Al6061
Effect of friction stir processing with different pass numbers on the mechanical, tribological and corrosion properties of Al6061 [Volume 5, Issue 3, 2018, Pages 12-21]
-
Al6061
Investigating the effect of pin and shoulder rotational speed on the mechanical properties of friction stir processed region in Al6061 [Volume 7, Issue 3, 2020, Pages 34-41]
-
Al 7075
Performance Evaluation of Self-propelled Rotary Tool in Turning [(Articles in Press)]
-
Alloy A356
Experimental study of mechanical properties and morphology of parts made by lost foam casting for A356-Alloy [Volume 6, Issue 1, 2019, Pages 42-52]
-
Al/Mg composite
Investigation of forming limit of multi-layered composite processed by roll bonding method [Volume 6, Issue 7, 2019, Pages 12-23]
-
Alternating magnetic field
Mathematical and experimental modeling of plasma channel radius in alternating magnetic field assisted electric discharge machining process [Volume 9, Issue 11, 2022, Pages 54-65]
-
Alumina
Designing and manufacturing of functional diffusive machine and its performance evaluation in the fabrication of Al-Al2O3 samples [Volume 6, Issue 3, 2019, Pages 8-19]
-
Alumina
Investigation of physical and mechanical properties of 3D printed parts by using of ABS plastic filaments filled by alumina [Volume 7, Issue 4, 2020, Pages 1-9]
-
Aluminum
The effect of temperature on tensile behavior and microstructure of Al-3 vol% SiC nanocomposite [Volume 5, Issue 2, 2018, Pages 1-8]
-
Aluminum
Designing and manufacturing of functional diffusive machine and its performance evaluation in the fabrication of Al-Al2O3 samples [Volume 6, Issue 3, 2019, Pages 8-19]
-
Aluminum
Investigation of the energy absorption in three-layer Al/Polypropylene/Steel deep drawn cups [Volume 7, Issue 6, 2020, Pages 34-43]
-
Aluminum
Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
-
Aluminum
Effect of weight percentage of alumina on mechanical properties of nanocomposite produced by additive manufacturing method of digital light processing [Volume 10, Issue 5, 2023, Pages 57-67]
-
Aluminum
Investigating the energy absorption of sandwich panel with aluminum core and skin under Quasi-static loading: A numerical and experimental study [(Articles in Press)]
-
Aluminum 6061-T6
Investigating the effect of the ultrasonic hammer peening on the wear properties of Aluminum alloy 6061 [(Articles in Press)]
-
Aluminum 6061-T6 alloy
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Aluminum 7075
Composite fabrication and surface reinforcement of aluminum 7075 by pumice micro and nanoparticles using the friction stir process (FSP) [Volume 7, Issue 5, 2020, Pages 56-63]
-
Aluminum 7075
Analysis of the effect of the hot stamping process on mechanical properties of 7075 aluminum alloy sheet [Volume 10, Issue 5, 2023, Pages 68-78]
-
Aluminum Alloy
Fabrication of two layer Al/Cu rods using hot forward extrusion [Volume 6, Issue 4, 2019, Pages 7-13]
-
Aluminum alloy 2014-T6
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2022, Pages 45-53]
-
Aluminum alloy 5052
Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
-
Aluminum alloy 5083
Experimental study of the effect of temperature on mechanical properties of aluminum sheets produced by equal channel angular rolling process [Volume 6, Issue 9, 2019, Pages 13-24]
-
Aluminum alloy 6061 sheet
Experimental study of the effects of constrained groove pressing process on AA6061 sheet [(Articles in Press)]
-
Aluminum Alloy 6061-T6
Investigation the effect of bobbin tool geometry in friction stir welding of aluminum alloy 6061-T6 [Volume 6, Issue 4, 2019, Pages 1-6]
-
Aluminum alloy . Experimental design
The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
-
Aluminum alloys
Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
-
Aluminum based composite
Production of aluminum-based composites from recycled chips by hot extrusion processing [(Articles in Press)]
-
Aluminum - Brass alloy
Investigation of Corrosion of Aluminum – Brass Alloy in Desalination Plant of South Pars Gas Complex [Volume 7, Issue 2, 2020, Pages 17-25]
-
Aluminum-ceramic composite
Experimental investigation and ANN prediction of Al-SiC nano-composite properties produced using dynamic compaction method [Volume 7, Issue 1, 2020, Pages 13-25]
-
Aluminum foam
Experimental Investigation of Aluminum Foam Sandwich Panels under Quasi-static Loading [Volume 7, Issue 7, 2020, Pages 14-23]
-
Aluminum foam
Experimental study on manufacturing of bi-metal sandwiches with aluminum foam core and copper layers using friction stir welding [Volume 7, Issue 12, 2020, Pages 1-9]
-
Aluminum foam
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
-
Aluminum matrix composite
Microstructure and mechanical properties of AA5456/SiO2p nanocomposite fabricated by friction stir processing [Volume 7, Issue 4, 2020, Pages 39-47]
-
Aluminum powder
Experimental and numerical investigation of the effect of metal powder particle size on the physical and mechanical properties of the components produced by high rate dynamic powder compaction [Volume 6, Issue 9, 2019, Pages 45-53]
-
Aluminum-silicon carbide nanocomposite
Statistical Analysis and Optimization of Friction Stir Additive Manufacturing Process Variables for Aluminum Silicon Carbide Nanocomposite Using the Response Surface Method [(Articles in Press)]
-
Aluminum tube
Experimental investigation of explosive forming of aluminum tubes using gas mixture [Volume 6, Issue 5, 2019, Pages 18-24]
-
AM60 magnesium alloy
The influences of radial-forward-backward extrusion on the microstructure and mechanical evolution of AM60 magnesium alloy by experimental and finite element micromechanical based cellular automaton approach [Volume 7, Issue 9, 2020, Pages 25-41]
-
AM60 magnesium alloy
Study of the cyclic extrusion–compression in production of high stringed and ultrafine grained AM60 Magnesium noncircular thin section beams [Volume 10, Issue 5, 2023, Pages 1-18]
-
Analysis of variance
Experimental and Numerical Study of Double Y-Shaped Hydroforming Using Analysis of Variance Method [Volume 6, Issue 7, 2019, Pages 34-41]
-
Analytical model
Analytical and experimental investigation of influence of rotational speed and feed on temperature elevation in cortical bone drilling [Volume 7, Issue 3, 2020, Pages 22-33]
-
Analytical Solution
Chatter stability investigation of micro-milling dental bur at enamel and dentin layers [Volume 7, Issue 7, 2020, Pages 1-13]
-
ANFIS
The use of neuro-fuzzy network coupled with meta-heuristic learning methods to predict surface roughness in the machining of aluminum alloys [(Articles in Press)]
-
ANFIS-GA
The use of neuro-fuzzy network coupled with meta-heuristic learning methods to predict surface roughness in the machining of aluminum alloys [(Articles in Press)]
-
Angular effect
Using Micro/Nano Scale Contact Models in 3D Manipulation of Deformation of Au Particles Under Angular Effect [Volume 7, Issue 5, 2020, Pages 33-43]
-
Annealing
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Ansys
Topology Optimization Of Structures With Thermal And Mechanical Loading [Volume 7, Issue 12, 2020, Pages 54-63]
-
Antioxidant additive
Study of the performance of minimum quantity lubrication (MQL) and type of lubricant in the milling process of stainless steel EN 1.4903 [Volume 6, Issue 3, 2019, Pages 28-42]
-
API X65 Steel
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Arduino board
Utilizing CNC technology in two-dimensional drawing and painting using a spray paint nozzle [(Articles in Press)]
-
Array Halbach
Design of a new actuator for actuating a linear hydraulic valve and its optimization with genetic algorithm [Volume 4, Issue 1, 2017, Pages 1-9]
-
Artificial Bee Colony
Identifying the mechanical properties of chromium nanobeams with artificial bee colony optimization method based on large deflection analysis with surface effects [Volume 10, Issue 4, 2023, Pages 48-61]
-
Artificial bee colony optimization
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Artificial finger
Design and implementation of a 2DOF human finger using shape memory alloys with computer-based online force control [Volume 5, Issue 4, 2018, Pages 44-55]
-
Artificial Neural Network
Experimental and numerical investigation of the effect of metal powder particle size on the physical and mechanical properties of the components produced by high rate dynamic powder compaction [Volume 6, Issue 9, 2019, Pages 45-53]
-
Artificial Neural Network
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2022, Pages 35-44]
-
Artificial Neural Networks
Experimental investigation and ANN prediction of Al-SiC nano-composite properties produced using dynamic compaction method [Volume 7, Issue 1, 2020, Pages 13-25]
-
Assembly Lines
Determining the order of products entering the mixed-model assembly line using the exact methods [Volume 9, Issue 8, 2022, Pages 44-55]
-
Asymmetrical rolling
Analytical investigation of unbounded clad sheets by utilizing slab method and employing hybrid friction through asymmetrical rolling [Volume 6, Issue 3, 2019, Pages 51-64]
-
ATI425 alloy
Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
-
Atomic Force Microscope
Using Micro/Nano Scale Contact Models in 3D Manipulation of Deformation of Au Particles Under Angular Effect [Volume 7, Issue 5, 2020, Pages 33-43]
-
Atomic Force Microscope
An Examination of Environmental and Dimensional Parameters on Force and Critical Time of the Manipulation Process Using the Mechanical Theory of DMT Contact [Volume 7, Issue 9, 2020, Pages 1-9]
-
Austenitization and quenching process
The effects of Cr addition on the phase transformation, microstructure and
mechanical properties of advanced high-strength steel [Volume 7, Issue 8, 2020, Pages 45-53]
-
Automatic positioning system
Automation of sheet metal positioning in stamping die design [Volume 8, Issue 1, 2021, Pages 55-67]
-
AZ31B
Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
-
AZ61 Mg alloy
Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process [Volume 6, Issue 1, 2019, Pages 53-60]
B
-
Backing plate material
Optimization of friction stir spot welding process parameters to achieve maximum failure load [Volume 5, Issue 1, 2018, Pages 13-27]
-
Bagasse fibers
Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
-
Ball-end Mill
Investigating the effect of sculptured surface curvatures on milling forces [Volume 6, Issue 6, 2019, Pages 34-43]
-
Ballistic impact
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Barium titanate
Experimental study of piezoelectric properties in barium titanate implants and 3D bone scaffolds [Volume 4, Issue 2, 2017, Pages 1-9]
-
Basalt fibers
Experimental study of the effect of cryogenic cycling and metal surface treatment on flexural properties of aluminum- epoxy/basalt fibers laminate composite [Volume 4, Issue 1, 2017, Pages 15-24]
-
Basalt fibers
Experimental investigation of flexural behavior of basalt fibers/epoxy-aluminum laminate composites containing nanoclay particles [Volume 5, Issue 1, 2018, Pages 45-54]
-
Base Armor Plate
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Bearing Test Equipment
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Bending
The use of magnetic field to reduce the spring back in bending of aluminum sheet 1050 [(Articles in Press)]
-
Bending Test
Manufacture and Comparison of Mechanical Properties of Reinforced Polypropylene Nanocomposite with Carbon Fibers and Calcium Carbonate Nanoparticles [Volume 6, Issue 5, 2019, Pages 1-12]
-
Bilayer Sheet
Numerical and experimental analysis of damage in the single point incremental forming of Aluminum/Copper bilayer sheet [Volume 10, Issue 1, 2023, Pages 20-29]
-
Bi-Metal Sandwich
Experimental study on manufacturing of bi-metal sandwiches with aluminum foam core and copper layers using friction stir welding [Volume 7, Issue 12, 2020, Pages 1-9]
-
Bio-composite
Effect of magnesium particle size on compressive strength of Mg/Hydroxyapatite porous bio-composite [Volume 10, Issue 2, 2023, Pages 33-40]
-
Biofilm
Theoretical and experimental analysis of the dental scaling tool geometry by ultrasonic waves on the rate of descaling [(Articles in Press)]
-
Bio Nano Particles
Experimental study of the effect of nanoparticles produced from sugarcane bagasse charcoal (nano biochar) on the anti-wear properties of lubricants used in bearing housing of centrifugal pumps in the petrochemical industry [(Articles in Press)]
-
Block and Palm
Theoretical and numerical investigation of workpiece jamming in fixture using block and palm case study [Volume 6, Issue 3, 2019, Pages 20-27]
-
Bobbin Tool
Investigation the effect of bobbin tool geometry in friction stir welding of aluminum alloy 6061-T6 [Volume 6, Issue 4, 2019, Pages 1-6]
-
Bobbin Tool
Assessment of using the floating bobbin tool for double sided friction stir welding of aluminium [Volume 7, Issue 3, 2020, Pages 52-62]
-
Bobbin Tool
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Bobbin Tool
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Body Implant
The effect of interlayer adhesion in predicting fatigue failure of 3D printed parts [(Articles in Press)]
-
Bolted joint
Experimental evaluation of joint strength in polypropylene-glass fiber reinforced composites under tensile load [Volume 6, Issue 2, 2019, Pages 39-46]
-
Bone
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2022, Pages 54-62]
-
Bone Los
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Bone scaffold
Experimental study of piezoelectric properties in barium titanate implants and 3D bone scaffolds [Volume 4, Issue 2, 2017, Pages 1-9]
-
Bone tissue engineering
Fabrication of polyethylene glycol composite with silicon carbide scaffold for use in bone tissue engineering [Volume 10, Issue 3, 2023, Pages 9-17]
-
Boring Bar
Investigation of dynamic absorber parameters to improve the vibration behavior of boring bar [Volume 9, Issue 7, 2022, Pages 1-8]
-
Boron carbide
Experimental study of the effect of electrical discharge machining parameters on surface roughness and Material removal rate of boron carbide ceramic [Volume 7, Issue 11, 2020, Pages 42-51]
-
Boundary Elements Method (BEM)
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2022, Pages 1-12]
-
Branch
Investigation of Effect of Process Parameters on Protrusion Height of Branched Parts in Tube Hydroforming [Volume 10, Issue 1, 2023, Pages 38-48]
-
Brazing
Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
-
Brazing
Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
-
Brazing
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Brittle porous structure
An experimental and numerical study of tool geometry effect on microfracture characteristics in micro/nano machining of brittle porous structure [Volume 6, Issue 5, 2019, Pages 47-52]
-
Buckling
Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
-
Buckling
Buckling and bending analysis of functional porous plate using shear deformation theory [Volume 9, Issue 8, 2022, Pages 34-43]
-
Burr formation
Optimization of surface roughness, striation and burr formation during machining of aluminum 2024-T351 with abrasive water jet machining [Volume 7, Issue 10, 2020, Pages 12-25]
-
Burst pressure
Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
C
-
Calcium Carbonate Nanoparticles
Manufacture and Comparison of Mechanical Properties of Reinforced Polypropylene Nanocomposite with Carbon Fibers and Calcium Carbonate Nanoparticles [Volume 6, Issue 5, 2019, Pages 1-12]
-
Calibration
Design, manufacturing and calibration of a micro syringe pump for micro-fluidics applications [(Articles in Press)]
-
Capacitive encoder
Resolution Improvement of a Capacitive-type linear Encoder with Untethered Slider [Volume 5, Issue 4, 2018, Pages 1-12]
-
CAPP
Process planning of cylindrical parts via by variant and generative methods and using of STEP file features [Volume 6, Issue 9, 2019, Pages 1-12]
-
Carbon Fiber composite
Comparison of dynamic behavior of steel and aluminum materials with epoxy composite reinforced with carbon and glass fibers by FEM [Volume 10, Issue 6, 2023, Pages 40-52]
-
Carbon Fibers
Manufacture and Comparison of Mechanical Properties of Reinforced Polypropylene Nanocomposite with Carbon Fibers and Calcium Carbonate Nanoparticles [Volume 6, Issue 5, 2019, Pages 1-12]
-
Carbon Fibers Reinforced Composite
Enhancing dimensional accuracy of the produced holes in CFRP by ultrasonic vibration assistance [Volume 10, Issue 3, 2023, Pages 1-8]
-
Carbon-phenolic composite
The effect of knurling surface treatment on the strength of adhesively bonding between steel plate and carbon-phenolic composite [Volume 7, Issue 5, 2020, Pages 44-55]
-
Catalyst
Synthesis of CuNiF and CoMnF nano ferrites by sol-gel combustion method and their catalytic influence on thermal decomposition behavior of ammonium perchlorate nanoparticles [Volume 7, Issue 10, 2020, Pages 26-33]
-
Cavitation
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Cavitation
Theoretical and experimental analysis of the dental scaling tool geometry by ultrasonic waves on the rate of descaling [(Articles in Press)]
-
Cell size
Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
-
Cellular Automaton (CA)
The influences of radial-forward-backward extrusion on the microstructure and mechanical evolution of AM60 magnesium alloy by experimental and finite element micromechanical based cellular automaton approach [Volume 7, Issue 9, 2020, Pages 25-41]
-
Cellular Automaton (CA)
Study of the cyclic extrusion–compression in production of high stringed and ultrafine grained AM60 Magnesium noncircular thin section beams [Volume 10, Issue 5, 2023, Pages 1-18]
-
Cellular structure
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Centrifugal method
Study on the mechanical properties of functionally graded material made by centrifugal method [Volume 7, Issue 4, 2020, Pages 10-18]
-
Cepstrum analysis
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
CFRP
Study of damage in CFRP and GFRP composite in drilling [Volume 6, Issue 6, 2019, Pages 44-50]
-
Channel and curvature angles
Simulation study of the effect of different channel and curvature angles on the effective strain and process load in the tubular channel angular pressing (TCAP) process using a trapezoidal channel cross-section [Volume 10, Issue 1, 2023, Pages 30-37]
-
Channel Depth
Investigating the effect of flexible forming process variables on the uniformity of thickness distribution in U-Shaped Micro-channels [Volume 10, Issue 2, 2023, Pages 41-48]
-
Characterization
Manufacturing and characterization of copper nano particles by ultrasonic-assisted electrical discharge machining [Volume 6, Issue 1, 2019, Pages 24-31]
-
Charpy impact
Investigation the interface and charpy impact behavior of fiber metal laminates containing graphene nanoplatelets and glass kevlar hybrid fibers [Volume 6, Issue 2, 2019, Pages 10-19]
-
Chatter
Investigation of tool and workpiece clamping effect on stability lobes in milling process [Volume 6, Issue 6, 2019, Pages 12-24]
-
Chatter phenomena Control
The new approach to practical predicting and controlling the chatter phenomenon in the internal turning process [Volume 5, Issue 4, 2018, Pages 56-73]
-
Check valve
Analysis and investigation of the characteristics of the flow and the force on the poppet including the edge of the flow deviation in the hydraulic check valve [(Articles in Press)]
-
CHIP
Studying the effects of preheat temperature on the turning process of CK45 steel [Volume 10, Issue 2, 2023, Pages 22-32]
-
Chip formation
Performance Evaluation of Self-propelled Rotary Tool in Turning [(Articles in Press)]
-
Chip Formation Energy
Study and investigation of cutting energy and chip formation in the grinding process of polyether ether ketone [Volume 7, Issue 7, 2020, Pages 51-58]
-
Chromite
Design and construction of advanced sorting inorder to chromite segregation [Volume 9, Issue 3, 2022, Pages 11-17]
-
Chromium
The effects of Cr addition on the phase transformation, microstructure and
mechanical properties of advanced high-strength steel [Volume 7, Issue 8, 2020, Pages 45-53]
-
Chromium nanobeam
Identifying the mechanical properties of chromium nanobeams with artificial bee colony optimization method based on large deflection analysis with surface effects [Volume 10, Issue 4, 2023, Pages 48-61]
-
Circular plate
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
CK45 steel
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
CK45 steel
Studying the effects of preheat temperature on the turning process of CK45 steel [Volume 10, Issue 2, 2023, Pages 22-32]
-
CK45 steel
Evaluation of the effects of immersion cooling grinding (ICG) method on the surface characteristics and microstructural changes in grinding of CK45 steel [(Articles in Press)]
-
Cleaning
Experimental study of the plasma electrolyte cleaning using different signal shapes [Volume 8, Issue 8, 2021, Pages 1-11]
-
Clinching
The effect of the die geometry on the joint strength of Al 3105 aluminum sheets joined by the clinching process [Volume 7, Issue 12, 2020, Pages 10-23]
-
Clinking process
Experimental investigation of the joinability of three-layer aluminum/ polymer/ aluminum composite sheets by the clinching process [Volume 8, Issue 4, 2021, Pages 27-38]
-
Closed cell foam
Experimental and numerical analysis of parameters affecting the mechanical behavior of closed cell aluminum foam in low-speed impact [Volume 9, Issue 12, 2022, Pages 43-53]
-
CMT process
Investigating the effect of CMT (Cold Metal Transfer) process on dilution of the Stellite 6 overlay [Volume 7, Issue 1, 2020, Pages 53-59]
-
CNG fuel tank
Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
-
Coating thickness"
The effect of continuous hot-dip galvanized steel coating thickness on the properties of dissimilar steel-magnesium joining using resistance spot welding [(Articles in Press)]
-
Cold Fluid
Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
-
Cold Re-Shape Rolling
Investigating the effect of different parameters on the occurrence of collapse defect in re-shape rolling of circular pipe into a square tube [Volume 6, Issue 4, 2019, Pages 14-22]
-
Cold roll-forming
Numerical and experimental study of the edge wrinkling defect of cold roll forming of wide profiles [Volume 5, Issue 1, 2018, Pages 28-36]
-
Cold roll-forming
Numerical and experimental investigation of the joint type effect on the heat created in weld metal in the pipe welded by high frequency induction welding [Volume 7, Issue 9, 2020, Pages 10-24]
-
Collapse Defect
Investigating the effect of different parameters on the occurrence of collapse defect in re-shape rolling of circular pipe into a square tube [Volume 6, Issue 4, 2019, Pages 14-22]
-
Commercially pure titanium
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Composite
Investigating the effect of the passes number and changing the tool rotation direction on the distribution of reinforcing particles in the FSP [Volume 10, Issue 2, 2023, Pages 7-13]
-
Composite
Experimental study of energy absorption of sandwich panel with composite/elastomer skin [(Articles in Press)]
-
Composited nanoparticles
Investigating the effect of Silica/Magnesium hydroxide composite nanoparticles on the flexural properties of polymer-based nanocomposites [(Articles in Press)]
-
Composite Material
Experimental investigation of the compressive strength of polylactic acid/continuous glass fiber composite material produced with an extrusion-based 3D printer using the simultaneous impregnation system of fibers and polymer [(Articles in Press)]
-
Composite Pressure Vessel
Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
-
Composite Rupture disc
Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
-
Composites
Designing and manufacturing of functional diffusive machine and its performance evaluation in the fabrication of Al-Al2O3 samples [Volume 6, Issue 3, 2019, Pages 8-19]
-
Composites
Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
-
Composites
Investigation of Mechanical and Thermal Properties of Continuous Metal Wire Reinforced Samples in Fused Deposition Modeling for Shape Memory Stimulus [(Articles in Press)]
-
Composite sandwich panel
Investigation the effective parameters on damages induced in composite sandwich structures through drilling [Volume 4, Issue 2, 2017, Pages 51-60]
-
Composite shells
Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
-
Compression Molding
Effect of Infill Percentage and Raster Angle in Fused Deposition Modeling (FDM) Process on Shape Memory Properties of Poly (lactic acid) and Comparison with Compression Molding [Volume 7, Issue 5, 2020, Pages 14-23]
-
Compressive strength
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
-
Compressive strength
Effect of magnesium particle size on compressive strength of Mg/Hydroxyapatite porous bio-composite [Volume 10, Issue 2, 2023, Pages 33-40]
-
Compressive strength
Experimental investigation of the compressive strength of polylactic acid/continuous glass fiber composite material produced with an extrusion-based 3D printer using the simultaneous impregnation system of fibers and polymer [(Articles in Press)]
-
Computer aided process planning
Development an advanced neural network for recognition of machining feature [Volume 9, Issue 5, 2022, Pages 1-12]
-
COMSOL
Theoretical and experimental analysis of the dental scaling tool geometry by ultrasonic waves on the rate of descaling [(Articles in Press)]
-
Conduction
Investigating electrical resistance and thermal analysis of hot spinning of titanium using resistance method [(Articles in Press)]
-
Constitutive equation
Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
-
Constitutive equations
Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
-
Constraint forces
A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
-
Contact area deformation
Using Micro/Nano Scale Contact Models in 3D Manipulation of Deformation of Au Particles Under Angular Effect [Volume 7, Issue 5, 2020, Pages 33-43]
-
Contact Mechanics Model
An Examination of Environmental and Dimensional Parameters on Force and Critical Time of the Manipulation Process Using the Mechanical Theory of DMT Contact [Volume 7, Issue 9, 2020, Pages 1-9]
-
Contact point
Analytical investigation of unbounded clad sheets by utilizing slab method and employing hybrid friction through asymmetrical rolling [Volume 6, Issue 3, 2019, Pages 51-64]
-
Continues cleaning
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Continuous fiber composite
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Continuous glass fibers
Deposition of Continuous Glass Fibers on a Curved Surface by 3D Printer Based on Fused Filament Fabrication Technology [(Articles in Press)]
-
Continuous metal wire
Investigation of Mechanical and Thermal Properties of Continuous Metal Wire Reinforced Samples in Fused Deposition Modeling for Shape Memory Stimulus [(Articles in Press)]
-
Continuous Ultrasonic Welding
Numerical Modeling of Roller Tools for Ultrasonic Welding of Thermoplastic Materials [Volume 5, Issue 2, 2018, Pages 26-33]
-
Convolutional Neural Networks
Development an advanced neural network for recognition of machining feature [Volume 9, Issue 5, 2022, Pages 1-12]
-
Cooling environment
Effect of Temper and Quench Heat Treatment on Mechanical Properties and Microstructure of AISI 4130 to AISI 4340 Steel Joint with GTAW Process [(Articles in Press)]
-
Coordinate Transformation
Utilizing CNC technology in two-dimensional drawing and painting using a spray paint nozzle [(Articles in Press)]
-
Copper - Austenitic Stainless Steel
Investigating the Effective Parameters in the Spring Back of Two Layers Sheet Copper-Austenitic Stainless Steel in the Incremental Sheet Forming [Volume 6, Issue 8, 2019, Pages 10-20]
-
Cored diamond tool
Enhancing dimensional accuracy of the produced holes in CFRP by ultrasonic vibration assistance [Volume 10, Issue 3, 2023, Pages 1-8]
-
Correction factor
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Corrosion Resistance
Investigation of Corrosion of Aluminum – Brass Alloy in Desalination Plant of South Pars Gas Complex [Volume 7, Issue 2, 2020, Pages 17-25]
-
Corrosion Resistance
Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
-
CP- aluminum
Assessment of using the floating bobbin tool for double sided friction stir welding of aluminium [Volume 7, Issue 3, 2020, Pages 52-62]
-
Crack
Analysis of a Crotch corner crack in the shell-nozzle junction of a cylindrical pressure vessel under internal pressure using the J-integral method [(Articles in Press)]
-
Crack detection
Identification of cracks in gas pipes using digital radiography, wavelet and curvelet transforms [Volume 7, Issue 2, 2020, Pages 26-32]
-
Creep
Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
-
Creep
Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
-
Crow Search Algorithm
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Crushing Force
Experimental and numerical investigation of energy absorption capability of holed thin-walled circular aluminum tubes under axial compression loading [Volume 10, Issue 6, 2023, Pages 29-39]
-
Crushing test
The effect of surface shape on the production of aluminum-copper two layer tubes using forward extusion process [Volume 6, Issue 8, 2019, Pages 1-9]
-
Cryogenic cooling
The effect of cryogenic cooling on surface topography in the PEEK grinding process [Volume 7, Issue 1, 2020, Pages 1-12]
-
Cryogenic cycling
Experimental study of the effect of cryogenic cycling and metal surface treatment on flexural properties of aluminum- epoxy/basalt fibers laminate composite [Volume 4, Issue 1, 2017, Pages 15-24]
-
Crystallographic texture
Texture evolution of 409 ferritic stainless steel tubes through severe plastic deformation and subsequent annealing [Volume 7, Issue 2, 2020, Pages 42-48]
-
Crystal Percentage
Investigation and effect of number of recycling steps on molten flow rate and crystalline percent in injection process in wood-plastic composite [Volume 6, Issue 3, 2019, Pages 1-7]
-
Curved irradiating scheme
Numerical investigation of deformation behavior in laser bending of sheet with curved irradiating scheme [Volume 9, Issue 2, 2022, Pages 1-7]
-
Curved Surfaces
Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
-
Curved Surfaces
Deposition of Continuous Glass Fibers on a Curved Surface by 3D Printer Based on Fused Filament Fabrication Technology [(Articles in Press)]
-
Curvilinear fiber
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Cut-off Turning
Design and Simulation of Magneto-Rheological (MR) Fluid Damper and
Experimental Study of its Effect on Tool Vibrations in Cut-off Operation [Volume 7, Issue 12, 2020, Pages 24-36]
-
Cutting fluid
Theoretical and Experimental Study of the Chatter Vibration in Dry and Wet Machining Conditions in the Turning Process [Volume 7, Issue 3, 2020, Pages 1-21]
-
Cutting force
Quantitative study of forces in boring process and a new method for tool-tip force [Volume 4, Issue 2, 2017, Pages 10-23]
-
Cutting force
Modeling and optimization of cutting force and surface roughness in the milling process of Inconel 738 by Neural Network and Genetic Algorithm [Volume 6, Issue 5, 2019, Pages 25-38]
-
Cutting force
The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
-
Cutting Force Coefficients
Simulation and modeling of dental bur force and vibration at enamel and dentin layers [Volume 6, Issue 8, 2019, Pages 43-53]
-
Cutting Speed
Investigation of machining behavior of Polyether Ether Ketone in Single grit scratch test [Volume 6, Issue 9, 2019, Pages 54-62]
-
Cutting torque
Experimental investigation of the simultaneous effect of machining parameters, axial force and cutting torque on the surface roughness of the produced hole in the drilling of the 7000 series AL Alloy workpiece [Volume 7, Issue 1, 2020, Pages 26-38]
-
Cyclic extrusion and compression
Study of the cyclic extrusion–compression in production of high stringed and ultrafine grained AM60 Magnesium noncircular thin section beams [Volume 10, Issue 5, 2023, Pages 1-18]
D
-
Damage
Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
-
Damage Criterion
Numerical and experimental analysis of damage in the single point incremental forming of Aluminum/Copper bilayer sheet [Volume 10, Issue 1, 2023, Pages 20-29]
-
Damage index
Diagnosis and evaluation of factors affecting corrosion damage detection in health monitoring of cantilever beam by electromechanical impedance method [Volume 7, Issue 7, 2020, Pages 59-70]
-
Damage model
Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
-
Damage model
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Damping Ratio
Experimental evaluation of the effect of the mass of ZnO, Nio, Fe3O4, Cdo nanoparticles on the damping ratio of Nano-fluid with glycerin base [Volume 7, Issue 2, 2020, Pages 8-16]
-
Deep drawing
Investigation of the energy absorption in three-layer Al/Polypropylene/Steel deep drawn cups [Volume 7, Issue 6, 2020, Pages 34-43]
-
Deep Learning
Development an advanced neural network for recognition of machining feature [Volume 9, Issue 5, 2022, Pages 1-12]
-
Defects
Analysis of crack behavior caused by corrosion in metal vessel repaired with composite under monotonic loading [Volume 10, Issue 3, 2023, Pages 34-42]
-
Defect size
Non-destructive measurement of internal defects using shear laser interferometry method [Volume 7, Issue 1, 2020, Pages 45-52]
-
Deflection
Identifying the mechanical properties of chromium nanobeams with artificial bee colony optimization method based on large deflection analysis with surface effects [Volume 10, Issue 4, 2023, Pages 48-61]
-
Deformation behavior
Numerical investigation of deformation behavior in laser bending of sheet with curved irradiating scheme [Volume 9, Issue 2, 2022, Pages 1-7]
-
Deformation index
Investigating the microstructure, mechanical properties and hole expansion of advanced high strength steel with the approach of application in the car body [Volume 10, Issue 6, 2023, Pages 16-28]
-
Deformation mechanism
Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
-
Delamination
The effect of drill geometrical properties on delamination and diameter error of holes in a thin sheet of Kevlar/epoxy composite [Volume 5, Issue 2, 2018, Pages 9-17]
-
Delamination
Study of damage in CFRP and GFRP composite in drilling [Volume 6, Issue 6, 2019, Pages 44-50]
-
Delamination
Comparison of wear behavior of an alloy developed as TRIP steel and DP steel [Volume 7, Issue 4, 2020, Pages 48-54]
-
Delamination
Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
-
Delamination
Investigating the effect of fiber angle on the quality of the surface and delamination in the turning of epoxy composite reinforced with glass fiber [Volume 10, Issue 2, 2023, Pages 14-21]
-
Delamination
An experimental study on the influence of temperature and strain rate on the mechanical properties and delamination of GLARE 2/1 under bending load [Volume 10, Issue 4, 2023, Pages 37-47]
-
Delamination factor
Investigation the effective parameters on damages induced in composite sandwich structures through drilling [Volume 4, Issue 2, 2017, Pages 51-60]
-
Delamination factor
Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
-
Delta-Trip steel
Investigating the microstructure and mechanical properties of vanadium bearing delta-Trip Steel [(Articles in Press)]
-
Dental Bur
Simulation and modeling of dental bur force and vibration at enamel and dentin layers [Volume 6, Issue 8, 2019, Pages 43-53]
-
Deposition Geometry Control
Three-Dimensional Geometry Profile Extraction of Deposits Using Linear Laser Scanning in the Directed Energy Deposition Additive Manufacturing Method [(Articles in Press)]
-
Design of experiments
Investigating machining factors of recovery powder metallurgy parts, from filings and sintered by Design of experiments in conjunction with sensitivity analysis [Volume 7, Issue 7, 2020, Pages 24-37]
-
Design of Step Amplifiers
Investigation of material removal rate and surface quality of super clear crystal glass workpiece in the ultrasonic machining process [Volume 10, Issue 1, 2023, Pages 1-10]
-
Dielectric Constant
Experimental investigation of mechanical and electrical properties of semi-biodegradable polypropylene/hemp woven thermoplastic composite [Volume 10, Issue 4, 2023, Pages 62-77]
-
Dielectrophoresis
Separation of healthy sperms using dielectrophoresis and thigmotaxis phenomena [(Articles in Press)]
-
Die with full arrangement
Experimental and numerical study on the distribution of thickness and dimensional accuracy of AA 6061 in two-point incremental forming using flexible die [Volume 7, Issue 11, 2020, Pages 9-20]
-
Die with partial arrangement
Experimental and numerical study on the distribution of thickness and dimensional accuracy of AA 6061 in two-point incremental forming using flexible die [Volume 7, Issue 11, 2020, Pages 9-20]
-
Digital Image Correlation
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
Digital Light Processing
Effect of weight percentage of alumina on mechanical properties of nanocomposite produced by additive manufacturing method of digital light processing [Volume 10, Issue 5, 2023, Pages 57-67]
-
Digital shearography
Non-destructive measurement of internal defects using shear laser interferometry method [Volume 7, Issue 1, 2020, Pages 45-52]
-
Digital shearography
Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
-
Digital shearography
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Dilution
Investigating the effect of CMT (Cold Metal Transfer) process on dilution of the Stellite 6 overlay [Volume 7, Issue 1, 2020, Pages 53-59]
-
Dimensional Accuracy
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Dimensional Measurement
Design and construction of laser thickness measurement device and analysis the effect of variation of the scanning depth of field and ambient light intensity on the accuracy of point cloud [Volume 6, Issue 9, 2019, Pages 37-44]
-
Dimensional Tolerance
Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
-
Dimensional Tolerance
Enhancing dimensional accuracy of the produced holes in CFRP by ultrasonic vibration assistance [Volume 10, Issue 3, 2023, Pages 1-8]
-
Direct-drive Servo valve (DDV)
Design of a new actuator for actuating a linear hydraulic valve and its optimization with genetic algorithm [Volume 4, Issue 1, 2017, Pages 1-9]
-
Directed Energy Deposition
Three-Dimensional Geometry Profile Extraction of Deposits Using Linear Laser Scanning in the Directed Energy Deposition Additive Manufacturing Method [(Articles in Press)]
-
Displacement Volume
Presenting the mathematical model of the variable flow rate axial piston pump with the displacement control valve [Volume 10, Issue 4, 2023, Pages 1-16]
-
Dissimilar joints"
The effect of continuous hot-dip galvanized steel coating thickness on the properties of dissimilar steel-magnesium joining using resistance spot welding [(Articles in Press)]
-
Dissimilar welding
Dissimilar welding of 5xxx and 7xxx aluminum alloy by self-reacting friction stir welding method [Volume 8, Issue 1, 2021, Pages 1-13]
-
Distortion
Application of pre-heating in the reduction of distortion in the dissimilar joints welding SS type 304 and carbon steel A106-B [Volume 6, Issue 6, 2019, Pages 51-63]
-
Double-layered tube
Experimental and numerical study of the hydroforming process of copper-aluminum double layered tube [Volume 10, Issue 3, 2023, Pages 18-33]
-
DP steel
Comparison of wear behavior of an alloy developed as TRIP steel and DP steel [Volume 7, Issue 4, 2020, Pages 48-54]
-
Dressing
Investigation of the effects of wheel surface topography and coolant-lubricant types on wheel loading in grinding of Inconel 738 using image processing method [Volume 7, Issue 8, 2020, Pages 10-18]
-
Drill
The effect of drill geometrical properties on delamination and diameter error of holes in a thin sheet of Kevlar/epoxy composite [Volume 5, Issue 2, 2018, Pages 9-17]
-
Drilling
The effect of drill geometrical properties on delamination and diameter error of holes in a thin sheet of Kevlar/epoxy composite [Volume 5, Issue 2, 2018, Pages 9-17]
-
Drilling
Study of damage in CFRP and GFRP composite in drilling [Volume 6, Issue 6, 2019, Pages 44-50]
-
Drilling
Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
-
Drilling
Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
-
Drilling
Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
-
Drilling
Enhancing dimensional accuracy of the produced holes in CFRP by ultrasonic vibration assistance [Volume 10, Issue 3, 2023, Pages 1-8]
-
Drilling of laminated composites
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2022, Pages 19-31]
-
Drilling parameters
Investigation the effective parameters on damages induced in composite sandwich structures through drilling [Volume 4, Issue 2, 2017, Pages 51-60]
-
Drilling parameters
Analytical and experimental investigation of influence of rotational speed and feed on temperature elevation in cortical bone drilling [Volume 7, Issue 3, 2020, Pages 22-33]
-
Drilling Process
Experimental investigation of the simultaneous effect of machining parameters, axial force and cutting torque on the surface roughness of the produced hole in the drilling of the 7000 series AL Alloy workpiece [Volume 7, Issue 1, 2020, Pages 26-38]
-
Drill Tip Angle
The Effect of Screw Arrangement and Drilling Parameters on the Fracture Fixation Strength of Femoral Neck [(Articles in Press)]
-
Drinking Water
Experimental study on the indentation resistance of water pipelines repaired by polyester resins [Volume 6, Issue 6, 2019, Pages 1-11]
-
Drop weight tear test
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Dry turning
Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
-
Ductile Cast Iron
Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
-
Ductile fracture criteria
Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
-
Duplex stainless steel 2205
Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
-
Dynamic Absorber
Investigation of dynamic absorber parameters to improve the vibration behavior of boring bar [Volume 9, Issue 7, 2022, Pages 1-8]
-
Dynamic Chip Thickness
Simulation and modeling of dental bur force and vibration at enamel and dentin layers [Volume 6, Issue 8, 2019, Pages 43-53]
-
Dynamic compaction
Experimental investigation and ANN prediction of Al-SiC nano-composite properties produced using dynamic compaction method [Volume 7, Issue 1, 2020, Pages 13-25]
-
Dynamic deflection
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Dynamic Modeling
Dynamic modeling of an internal turning tool using experimental modal analysis and simulation of active vibration control [Volume 6, Issue 4, 2019, Pages 29-36]
-
Dynamic parameter identification
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Dynamic powder compaction
Experimental and numerical investigation of the effect of metal powder particle size on the physical and mechanical properties of the components produced by high rate dynamic powder compaction [Volume 6, Issue 9, 2019, Pages 45-53]
-
Dynamic recovery
Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
-
Dynamic recrystallization
Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
-
Dynamics of marine robotics
Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
E
-
ECAP
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
ECAR
Experimental study of the effect of temperature on mechanical properties of aluminum sheets produced by equal channel angular rolling process [Volume 6, Issue 9, 2019, Pages 13-24]
-
ECC
Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process [Volume 6, Issue 1, 2019, Pages 53-60]
-
Eccentric forming punch
Incremental forming of cylindrical aluminum flanges using a new eccentric tool [Volume 7, Issue 8, 2020, Pages 28-35]
-
Edge detection
Development & Application of Modulated IR Thermography in Non-destructive Evaluation of Composite Materials by an edge detection filter and a morphological attribute profile [Volume 5, Issue 1, 2018, Pages 55-62]
-
Edge wrinkling defect
Numerical and experimental study of the edge wrinkling defect of cold roll forming of wide profiles [Volume 5, Issue 1, 2018, Pages 28-36]
-
EDM process
Experimental evaluation of the simultaneous effect of Nanoparticle ZnO and spark peak current on MRR, surface roughness and surface micro cracks of the AISI1045، AISI 4140 و AISI D3 [Volume 7, Issue 10, 2020, Pages 46-60]
-
E -Fast
Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
-
E-fast statistical method
Investigating machining factors of recovery powder metallurgy parts, from filings and sintered by Design of experiments in conjunction with sensitivity analysis [Volume 7, Issue 7, 2020, Pages 24-37]
-
Effective strain
Simulation study of the effect of different channel and curvature angles on the effective strain and process load in the tubular channel angular pressing (TCAP) process using a trapezoidal channel cross-section [Volume 10, Issue 1, 2023, Pages 30-37]
-
Effective thermal conductivity
Microstructure design of heterogeneous material using multisided patch [Volume 8, Issue 2, 2021, Pages 32-40]
-
Effect of surface shape
The effect of surface shape on the production of aluminum-copper two layer tubes using forward extusion process [Volume 6, Issue 8, 2019, Pages 1-9]
-
Elasticity tensor
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Elasticity theory
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Electrical Discharge
Manufacturing and characterization of copper nano particles by ultrasonic-assisted electrical discharge machining [Volume 6, Issue 1, 2019, Pages 24-31]
-
Electrical Discharge
Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
-
Electrical Discharge Machining
Experimental Study of Material Removal Rate, Surface Roughness and Topography in Electrical Discharge Machining of Titanium Aluminide Intermetallic Compound [Volume 3, Issue 3, 2016, Pages 29-39]
-
Electrical Discharge Machining
Fractal-based analysis of the influence of current intensity on surface hardness and surface roughness of Steel workpiece in Electrical Discharge process [Volume 7, Issue 11, 2020, Pages 21-33]
-
Electrical Discharge Machining
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Electrical discharge machining (EDM)
Experimental study of the effect of electrical discharge machining parameters on surface roughness and Material removal rate of boron carbide ceramic [Volume 7, Issue 11, 2020, Pages 42-51]
-
Electrical Resistance Hot Spinning (ERHS)
Investigating electrical resistance and thermal analysis of hot spinning of titanium using resistance method [(Articles in Press)]
-
Electrochemical Corrosion
Study of the Electrochemical Corrosion Rate of Medical Implants of Titanium and Stainless Steel Made by Machining and selective laser melting under Different Surface Conditions [Volume 4, Issue 2, 2017, Pages 24-38]
-
Electrochemical Deburring
Experimental study of the effect of ultrasonic waves on the parameters of the electrochemical deburring process [Volume 10, Issue 2, 2023, Pages 1-6]
-
Electroforming
Effect of Electroforming Process Parameters with One-way Pulse Current and Reverse Pulse Current (PRC) on Mechanical Properties and Thickness Uniformity of Produced Copper U-shaped [Volume 7, Issue 10, 2020, Pages 61-72]
-
Electroless coating
Effect of SiO2 and MoS2 nanoparticles on microstructure and wear resistance of electroless nanocomposite Ni-P-SiO2-MoS2 coating [Volume 7, Issue 9, 2020, Pages 65-71]
-
Electromagnetic flow meter
Design and fabrication of electromagnetic arrayed flow meter to measure velocity profiles in a rectangular channel [Volume 8, Issue 12, 2021, Pages 21-33]
-
Electromagnetic pump
Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
-
Electromechanical Impedance
Monitoring and detection of corrosion defect in the inner wall of the metal tube by non-destructive electromechanical impedance method [Volume 7, Issue 6, 2020, Pages 8-17]
-
Electromechanical Impedance
Diagnosis and evaluation of factors affecting corrosion damage detection in health monitoring of cantilever beam by electromechanical impedance method [Volume 7, Issue 7, 2020, Pages 59-70]
-
Electron beam
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
Electroplastic effect
Experimental investigation of electroplastic effect on strain behavior of 6T-6061 aluminum sheet through uniaxial tensile test [(Articles in Press)]
-
Elemental Analysis
Experimental study of anti-wear performance of nano lubricants in rotary machines gearboxes [Volume 6, Issue 2, 2019, Pages 30-38]
-
Elemental Analysis Test
Experimental study of the effect of nanoparticles produced from sugarcane bagasse charcoal (nano biochar) on the anti-wear properties of lubricants used in bearing housing of centrifugal pumps in the petrochemical industry [(Articles in Press)]
-
Energy absorption
Investigation of the energy absorption in three-layer Al/Polypropylene/Steel deep drawn cups [Volume 7, Issue 6, 2020, Pages 34-43]
-
Energy absorption
Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
-
Energy absorption
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Energy absorption
Investigating the energy absorption quality of the porous Schwarz P structure made by 3D printing method [Volume 9, Issue 11, 2022, Pages 13-20]
-
Energy absorption
Numerical investigation of deformation behavior of aluminum beams reinforced with aluminum foam [Volume 10, Issue 1, 2023, Pages 49-58]
-
Energy absorption
Experimental study of energy absorption of sandwich panel with composite/elastomer skin [(Articles in Press)]
-
Energy absorption
Investigating the energy absorption of sandwich panel with aluminum core and skin under Quasi-static loading: A numerical and experimental study [(Articles in Press)]
-
Energy Absorption Capacity
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
-
Energy Storage
Synthesis and characterization of porous organic polymers based on diamine and trialdehyde for electrochemical energy storage [Volume 9, Issue 10, 2022, Pages 55-61]
-
Energy to Weight Ratio
Experimental and numerical investigation of energy absorption capability of holed thin-walled circular aluminum tubes under axial compression loading [Volume 10, Issue 6, 2023, Pages 29-39]
-
Engine parts
Fabrication and numerical analysis of glass fiber reinforced composite air manifold under vibration loading [Volume 7, Issue 12, 2020, Pages 64-75]
-
Epoxy-glass fiber composite
Experiment study of tensile behavior of self-healing polymer composite under heating cycles [Volume 5, Issue 2, 2018, Pages 18-25]
-
Equal Channel Angular Pressing
Experimental Investigation of the Effect of Equal Channel Angular Pressing Intermediate Canal of on the Mechanical Properties of Copper [Volume 6, Issue 1, 2019, Pages 32-41]
-
Experimental analysis
Analysis and investigation of the characteristics of the flow and the force on the poppet including the edge of the flow deviation in the hydraulic check valve [(Articles in Press)]
-
Experimental and numerical analysis
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Experimental and Theoretical Analysis
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Experimental modal analysis
Dynamic modeling of an internal turning tool using experimental modal analysis and simulation of active vibration control [Volume 6, Issue 4, 2019, Pages 29-36]
-
Experimental test
Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
-
Experimental test
Experimental investigation of damage in corrugated multilayer sandwich panel under quasi-static three-point bending [(Articles in Press)]
-
Explosive forming
Experimental investigation of explosive forming of aluminum tubes using gas mixture [Volume 6, Issue 5, 2019, Pages 18-24]
-
Explosive work-hardening
Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
-
Extruded Direction
Experimental investigation on the effect of thickness, heating time and extrude direction on thermal shrinkage and thickness variations ABS sheet in vacuum forming process [Volume 7, Issue 8, 2020, Pages 1-9]
-
Extrusion foam
Investigation of the effect of die diameter on the structural properties of extruded polyethylene foams [(Articles in Press)]
F
-
Failure analysis
Failure Mode, Effects & Criticality Analysis on C.N.C lathe engine spindle system in Uncertain Condition [(Articles in Press)]
-
Failure load
Optimization of friction stir spot welding process parameters to achieve maximum failure load [Volume 5, Issue 1, 2018, Pages 13-27]
-
Failure mode of joints
Optimization of friction stir spot welding process parameters to achieve maximum failure load [Volume 5, Issue 1, 2018, Pages 13-27]
-
Failure Pressure
Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
-
Failure zone
Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
-
Fatigue failure
The effect of interlayer adhesion in predicting fatigue failure of 3D printed parts [(Articles in Press)]
-
Fatigue life
The effect of current intensity and feed rate on surface roughness and fatigue life of work piece in wire electrical discharge turning (WEDT) process [Volume 7, Issue 8, 2020, Pages 36-44]
-
Fault Diagnosis
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
FDM
Influence of infill density and printing pattern on flexural properties of 3D printed short carbon fiber PLA composite [Volume 7, Issue 9, 2020, Pages 42-51]
-
FDM
Investigating the influencing parameters on the surface roughness of polymer parts by Fused Deposition Modeling with respect to laser polishing [(Articles in Press)]
-
Feature Extraction
Process planning of cylindrical parts via by variant and generative methods and using of STEP file features [Volume 6, Issue 9, 2019, Pages 1-12]
-
FEM
Numerical and experimented study of UFG pure copper with high strength processed by Accumulative compound extrusion (ACE) [Volume 7, Issue 3, 2020, Pages 42-51]
-
FEM
The influences of radial-forward-backward extrusion on the microstructure and mechanical evolution of AM60 magnesium alloy by experimental and finite element micromechanical based cellular automaton approach [Volume 7, Issue 9, 2020, Pages 25-41]
-
FEM
Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
-
FEM
Study of the cyclic extrusion–compression in production of high stringed and ultrafine grained AM60 Magnesium noncircular thin section beams [Volume 10, Issue 5, 2023, Pages 1-18]
-
FEM
The Effect of Screw Arrangement and Drilling Parameters on the Fracture Fixation Strength of Femoral Neck [(Articles in Press)]
-
FEM ANALYSIS
Evaluation and measurement of the residual stresses in stainless steel pipes and investigation of the effects of wall thickness on the stresses distribution [Volume 4, Issue 2, 2017, Pages 61-68]
-
FEM ANALYSIS
Numerical and Experimental Investigation of Performance of Styrene Butadiene Rubber, Polyurethane, and Polyvinyl Chloride in Outsoles Fabrication [Volume 7, Issue 6, 2020, Pages 56-64]
-
FEM modeling
Numerical Modeling of Roller Tools for Ultrasonic Welding of Thermoplastic Materials [Volume 5, Issue 2, 2018, Pages 26-33]
-
FEM modeling
Analytical and Numerical Investigation of Machining Forces of Ultrasonic Assisted Milling [Volume 7, Issue 4, 2020, Pages 31-38]
-
Femoral Neck Fracture
The Effect of Screw Arrangement and Drilling Parameters on the Fracture Fixation Strength of Femoral Neck [(Articles in Press)]
-
Ferritic stainless steel
Texture evolution of 409 ferritic stainless steel tubes through severe plastic deformation and subsequent annealing [Volume 7, Issue 2, 2020, Pages 42-48]
-
Fe/TiC surface composite
Mechanical behavior of Fe/ TiC surface layer fabricated by SMAW process [Volume 4, Issue 1, 2017, Pages 44-53]
-
Fiber metal laminate
Investigation the interface and charpy impact behavior of fiber metal laminates containing graphene nanoplatelets and glass kevlar hybrid fibers [Volume 6, Issue 2, 2019, Pages 10-19]
-
Fiber metal laminate
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Fiber-metal laminate
Experimental study of the effect of cryogenic cycling and metal surface treatment on flexural properties of aluminum- epoxy/basalt fibers laminate composite [Volume 4, Issue 1, 2017, Pages 15-24]
-
Fiber Metal Laminate, GLARE, Glass fiber, Poisson&rsquo
An experimental study of GLARE 2/1 and 3/2 tensile behavior using Digital Image Correlation [(Articles in Press)]
-
Fiber metal laminates
Experimental investigation of flexural behavior of basalt fibers/epoxy-aluminum laminate composites containing nanoclay particles [Volume 5, Issue 1, 2018, Pages 45-54]
-
Fiber metal laminates
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Fiber Orientation
Experimental investigation of the effect of ultrasonic welding parameters on the strength and weldability of GF/PA6 thermoplastic composites [Volume 10, Issue 5, 2023, Pages 44-56]
-
Fiber path
Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
-
Fiber twist angle
Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
-
Filler
Investigation of fire resistance and mechanical properties of Glass Fiber Reinforced Polyester composites in the presence of nanoclay, magnesium hydroxide, aluminum hydroxide, zinc oxide [Volume 6, Issue 2, 2019, Pages 1-9]
-
Fine blanking
Experimental and numerical investigation of the effect of die clearance on the cutting characteristics in the fine blanking of a complex part made of CK15 steel [(Articles in Press)]
-
Fine-grained material
Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
-
Finite Element
Optimization of welding parameters in resistance spot welding of AZ61 Mg alloy [Volume 5, Issue 3, 2018, Pages 44-51]
-
Finite Element
Numerical and experimental analysis of laser welding process parameters on weld bead geometry [Volume 7, Issue 3, 2020, Pages 63-71]
-
Finite Element
The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
-
Finite Element
Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
-
Finite Element
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Finite Element
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Finite Element
Analysis of the effect of the hot stamping process on mechanical properties of 7075 aluminum alloy sheet [Volume 10, Issue 5, 2023, Pages 68-78]
-
Finite Element
Comparison of dynamic behavior of steel and aluminum materials with epoxy composite reinforced with carbon and glass fibers by FEM [Volume 10, Issue 6, 2023, Pages 40-52]
-
Finite-Element Analysis (FEA)
Design of a new actuator for actuating a linear hydraulic valve and its optimization with genetic algorithm [Volume 4, Issue 1, 2017, Pages 1-9]
-
Finite element method
A numerical-experimental investigation on spring back in rectangular section thin wall hollows and extracting a relation to estimate twisted angle by considering strain harden behavior [Volume 4, Issue 1, 2017, Pages 38-43]
-
Finite element method
Investigating the effect of different parameters on the occurrence of collapse defect in re-shape rolling of circular pipe into a square tube [Volume 6, Issue 4, 2019, Pages 14-22]
-
Finite element method
Experimental and Numerical Study of Double Y-Shaped Hydroforming Using Analysis of Variance Method [Volume 6, Issue 7, 2019, Pages 34-41]
-
Finite element method
Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
-
Finite element method
Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
-
Finite element method
A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
-
Finite element method
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Finite element method
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2022, Pages 10-18]
-
Finite element method
Simulation study of the effect of different channel and curvature angles on the effective strain and process load in the tubular channel angular pressing (TCAP) process using a trapezoidal channel cross-section [Volume 10, Issue 1, 2023, Pages 30-37]
-
Finite element method
Numerical Simulation and fabrication of copper thin wall tube by constrained ironing method [(Articles in Press)]
-
Finite element method (FEM)
Strength analysis of long edge freight wagon underframe using finite element method [Volume 10, Issue 4, 2023, Pages 27-36]
-
Finite element method (FEM)
Analysis of a Crotch corner crack in the shell-nozzle junction of a cylindrical pressure vessel under internal pressure using the J-integral method [(Articles in Press)]
-
Finite element model
Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process [Volume 6, Issue 1, 2019, Pages 53-60]
-
Finite element model
Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
-
Finite elements
The effect of interlayer adhesion in predicting fatigue failure of 3D printed parts [(Articles in Press)]
-
Finite element simulation
Numerical and experimental study of the edge wrinkling defect of cold roll forming of wide profiles [Volume 5, Issue 1, 2018, Pages 28-36]
-
Finite element simulation
Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
-
Finite element simulation
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Finite element simulation
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Finite element simulation
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2022, Pages 1-9]
-
Finite element simulation
Investigation of Effect of Process Parameters on Protrusion Height of Branched Parts in Tube Hydroforming [Volume 10, Issue 1, 2023, Pages 38-48]
-
Finite element simulation
Experimental and numerical study of the hydroforming process of copper-aluminum double layered tube [Volume 10, Issue 3, 2023, Pages 18-33]
-
Finite element simulation
Experimental and numerical investigation of energy absorption capability of holed thin-walled circular aluminum tubes under axial compression loading [Volume 10, Issue 6, 2023, Pages 29-39]
-
Finite element simulation
Experimental and numerical investigation of the effect of die clearance on the cutting characteristics in the fine blanking of a complex part made of CK15 steel [(Articles in Press)]
-
Finite Elements Method
Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
-
Firmness index
Nondestructive investigating firmness of tuber agricultural products during storage using sound and compression tests [Volume 6, Issue 7, 2019, Pages 52-60]
-
Fixture Design
Theoretical and numerical investigation of workpiece jamming in fixture using block and palm case study [Volume 6, Issue 3, 2019, Pages 20-27]
-
Flexible Die Support
The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
-
Flexible roll forming
Numerical and experimental investigation of the effect of local heating on the reduction of the spring back defect in the flexible roll forming process [Volume 9, Issue 9, 2022, Pages 35-44]
-
Flexural Behavior
Optimization of manufacturing process of GlassPolycarbonate thermoplastic laminates using Taguchi method [Volume 5, Issue 4, 2018, Pages 37-43]
-
Flexural properties
Experimental study of the effect of cryogenic cycling and metal surface treatment on flexural properties of aluminum- epoxy/basalt fibers laminate composite [Volume 4, Issue 1, 2017, Pages 15-24]
-
Flexural properties
Investigating the effect of Silica/Magnesium hydroxide composite nanoparticles on the flexural properties of polymer-based nanocomposites [(Articles in Press)]
-
Flexural Strength
Study on the mechanical properties of functionally graded material made by centrifugal method [Volume 7, Issue 4, 2020, Pages 10-18]
-
Flexural Strength
Experimental study and statistical optimization of fabrication parameters affecting the flexural strength of composite grid-stiffened panels [Volume 8, Issue 11, 2021, Pages 1-15]
-
Flexural test
Experimental investigation of flexural behavior of basalt fibers/epoxy-aluminum laminate composites containing nanoclay particles [Volume 5, Issue 1, 2018, Pages 45-54]
-
Flow stress
Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
-
Fluid and robotic arms interaction
Design, modeling and motion simulation of robotic manipulators with time-varying structure in a fluid environment [Volume 9, Issue 2, 2022, Pages 41-51]
-
Foam Density
Experimental study of mechanical properties and morphology of parts made by lost foam casting for A356-Alloy [Volume 6, Issue 1, 2019, Pages 42-52]
-
Foam Density
Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
-
Folded cross section
Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
-
Force Control
Design and implementation of a 2DOF human finger using shape memory alloys with computer-based online force control [Volume 5, Issue 4, 2018, Pages 44-55]
-
Force model
Theoretical and Experimental Study of the Chatter Vibration in Dry and Wet Machining Conditions in the Turning Process [Volume 7, Issue 3, 2020, Pages 1-21]
-
Force prediction
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2022, Pages 54-62]
-
Formability
Experimental investigation of formability of laser tailor welded steel blanks in single point incremental forming [Volume 6, Issue 6, 2019, Pages 25-33]
-
Formability
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Formability index
Investigating the microstructure and mechanical properties of vanadium bearing delta-Trip Steel [(Articles in Press)]
-
Formation of bimetal tubes
The effect of surface shape on the production of aluminum-copper two layer tubes using forward extusion process [Volume 6, Issue 8, 2019, Pages 1-9]
-
Forming force
Investigating the Effective Parameters in the Spring Back of Two Layers Sheet Copper-Austenitic Stainless Steel in the Incremental Sheet Forming [Volume 6, Issue 8, 2019, Pages 10-20]
-
Forward extrusion
The effect of surface shape on the production of aluminum-copper two layer tubes using forward extusion process [Volume 6, Issue 8, 2019, Pages 1-9]
-
Forward pulse
Effect of Electroforming Process Parameters with One-way Pulse Current and Reverse Pulse Current (PRC) on Mechanical Properties and Thickness Uniformity of Produced Copper U-shaped [Volume 7, Issue 10, 2020, Pages 61-72]
-
Fourier series Descriptors
Dimensional control of sand particles based on the Iranian National Standard Organization using image processing technique [Volume 5, Issue 3, 2018, Pages 52-62]
-
Fractional Factorial Design
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2022, Pages 1-9]
-
Fracture fixation
The Effect of Screw Arrangement and Drilling Parameters on the Fracture Fixation Strength of Femoral Neck [(Articles in Press)]
-
Free-form surfaces
Free-form surface localization using surface partitioning and genetic algorithm [Volume 5, Issue 3, 2018, Pages 22-31]
-
Free surface
The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
-
Frequency domain decomposition method
Experimental evaluation of the effect of the mass of ZnO, Nio, Fe3O4, Cdo nanoparticles on the damping ratio of Nano-fluid with glycerin base [Volume 7, Issue 2, 2020, Pages 8-16]
-
Friction drilling
Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
-
Friction stir additive manufacturing
Statistical Analysis and Optimization of Friction Stir Additive Manufacturing Process Variables for Aluminum Silicon Carbide Nanocomposite Using the Response Surface Method [(Articles in Press)]
-
Friction stir consolidation
Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
-
Friction Stir Process
Investigating the effect of pin and shoulder rotational speed on the mechanical properties of friction stir processed region in Al6061 [Volume 7, Issue 3, 2020, Pages 34-41]
-
Friction Stir Process
Composite fabrication and surface reinforcement of aluminum 7075 by pumice micro and nanoparticles using the friction stir process (FSP) [Volume 7, Issue 5, 2020, Pages 56-63]
-
Friction Stir Process
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Friction Stir Processing
Effect of friction stir processing with different pass numbers on the mechanical, tribological and corrosion properties of Al6061 [Volume 5, Issue 3, 2018, Pages 12-21]
-
Friction Stir Processing
Evaluation of the effect of underwater friction stir welding on microstructure and tribological properties of copper and its alloy [Volume 6, Issue 7, 2019, Pages 42-51]
-
Friction Stir Processing
Microstructure and mechanical properties of AA5456/SiO2p nanocomposite fabricated by friction stir processing [Volume 7, Issue 4, 2020, Pages 39-47]
-
Friction-stirring process
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Friction stir spot welding
Optimization of friction stir spot welding process parameters to achieve maximum failure load [Volume 5, Issue 1, 2018, Pages 13-27]
-
Friction stir spot welding
Experimental investigation on mechanical properties affected by dissimilar friction stir spot welding of aluminum 6061-T6 alloy to copper [Volume 10, Issue 6, 2023, Pages 53-64]
-
Friction stir vibration processing
The effect of friction stir vibration processing on microstructure and mechanical properties of Al5052/SiC surface nano composite [Volume 6, Issue 1, 2019, Pages 1-11]
-
Friction Stir Welding
Investigation the effect of bobbin tool geometry in friction stir welding of aluminum alloy 6061-T6 [Volume 6, Issue 4, 2019, Pages 1-6]
-
Friction Stir Welding
Study of the effect of instrument pin geometry on mechanical and microstructural properties of the welding region in the process of friction stir butt welding of AlMg6 [Volume 6, Issue 9, 2019, Pages 25-36]
-
Friction Stir Welding
Assessment of using the floating bobbin tool for double sided friction stir welding of aluminium [Volume 7, Issue 3, 2020, Pages 52-62]
-
Friction Stir Welding
Experimental study on manufacturing of bi-metal sandwiches with aluminum foam core and copper layers using friction stir welding [Volume 7, Issue 12, 2020, Pages 1-9]
-
Friction Stir Welding
Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
-
Friction Stir Welding
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Friction stir welding process
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
FSP
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
FSP
Investigating the effect of the passes number and changing the tool rotation direction on the distribution of reinforcing particles in the FSP [Volume 10, Issue 2, 2023, Pages 7-13]
-
Fuel Flow Balancing
Arrangement of gas fuel nozzle in power plant turbines with the purpose of temperature spread control and based on gas fuel flow rate [(Articles in Press)]
-
Fuel Vessel
Analysis of crack behavior caused by corrosion in metal vessel repaired with composite under monotonic loading [Volume 10, Issue 3, 2023, Pages 34-42]
-
Full-discretization method
Investigation of tool and workpiece clamping effect on stability lobes in milling process [Volume 6, Issue 6, 2019, Pages 12-24]
-
Functional graded
Buckling and bending analysis of functional porous plate using shear deformation theory [Volume 9, Issue 8, 2022, Pages 34-43]
-
Functional graded material
Study on the mechanical properties of functionally graded material made by centrifugal method [Volume 7, Issue 4, 2020, Pages 10-18]
-
Functionally graded composite
Fabrication and Characterization of Functionally Graded in-situ Al/Al-Cu-Cr Composite by Centrifugal Casting Process [Volume 7, Issue 9, 2020, Pages 52-64]
-
Functionally graded materials (FGMs)
Designing and manufacturing of functional diffusive machine and its performance evaluation in the fabrication of Al-Al2O3 samples [Volume 6, Issue 3, 2019, Pages 8-19]
-
Fused deposition modeling 3D printer
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Fused deposition modeling (FDM)
Study on the effect of thickness of layers, temperature and speed of nozzle on circularity error and surface roughness of holes in parts produced during fused deposition modeling [Volume 7, Issue 7, 2020, Pages 38-50]
-
Fused deposition modeling (FDM)
Investigating the effect of build orientation on surface roughness and build time using Fused Deposition Modelling [Volume 7, Issue 12, 2020, Pages 37-53]
-
Fused deposition modeling (FDM)
Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
-
Fused deposition modeling (FDM)
The effect of interlayer adhesion in predicting fatigue failure of 3D printed parts [(Articles in Press)]
-
Fused Filament Fabrication
Comparison of Tensile Strength for 3D Printed Parts Fabricated by Fused Filament Fabrication (FFF) [Volume 9, Issue 5, 2022, Pages 40-48]
-
Fused Filament Fabrication
Deposition of Continuous Glass Fibers on a Curved Surface by 3D Printer Based on Fused Filament Fabrication Technology [(Articles in Press)]
-
Fuses Filament Fabrication (FFF)
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Fuzzy logic
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2022, Pages 54-62]
G
-
Galfenol
Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
-
Galvanized steel sheet"
The effect of continuous hot-dip galvanized steel coating thickness on the properties of dissimilar steel-magnesium joining using resistance spot welding [(Articles in Press)]
-
Gap function
Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
-
Gas gun
Experimental and numerical investigation of the effect of metal powder particle size on the physical and mechanical properties of the components produced by high rate dynamic powder compaction [Volume 6, Issue 9, 2019, Pages 45-53]
-
Gas-gun
Experimental investigation and ANN prediction of Al-SiC nano-composite properties produced using dynamic compaction method [Volume 7, Issue 1, 2020, Pages 13-25]
-
Gas Metal Arc Welding
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
Gas Pipeline
Experimental determination of position effect on mechanical and metallurgical properties of HSLA multi-pass girth weld at natural gas pipelines [Volume 5, Issue 4, 2018, Pages 13-25]
-
Gas Pipelines
Design and Manufacturing of the Magnetic Flux Leakage Inspection System for Detection of Pitting Corrosion in Gas Pipelines [Volume 5, Issue 2, 2018, Pages 43-49]
-
Gas turbine
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
-
Gas turbine
Arrangement of gas fuel nozzle in power plant turbines with the purpose of temperature spread control and based on gas fuel flow rate [(Articles in Press)]
-
Gas Turbine Blade
Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
-
Gearbox
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
Gecko-like adhesive
A Solenoid Actuated Gecko-like Robotic Gripper [Volume 6, Issue 3, 2019, Pages 43-50]
-
GE-F9
Arrangement of gas fuel nozzle in power plant turbines with the purpose of temperature spread control and based on gas fuel flow rate [(Articles in Press)]
-
Genetic Algorithm
Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
-
Genetic Algorithm
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Genetic Algorithm
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2022, Pages 35-44]
-
Geometrical Parameters
Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
-
Geometrical Tolerance
Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
-
Geometric parameters
Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
-
GFRP
Study of damage in CFRP and GFRP composite in drilling [Volume 6, Issue 6, 2019, Pages 44-50]
-
Girth weld
Experimental determination of position effect on mechanical and metallurgical properties of HSLA multi-pass girth weld at natural gas pipelines [Volume 5, Issue 4, 2018, Pages 13-25]
-
Glass/epoxy composite
Experimental and numerical investigation on crushing of metal-composite hybrid energy absorber under a quasi-static loading [Volume 6, Issue 8, 2019, Pages 54-66]
-
Glass/epoxy composite
Experimental Investigation of Aluminum Foam Sandwich Panels under Quasi-static Loading [Volume 7, Issue 7, 2020, Pages 14-23]
-
Glass/epoxy composites
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2022, Pages 19-31]
-
Glass Fiber Composite
Comparison of dynamic behavior of steel and aluminum materials with epoxy composite reinforced with carbon and glass fibers by FEM [Volume 10, Issue 6, 2023, Pages 40-52]
-
Glass fibers
Investigating the effect of thermal preloading of glass fiber fabric on changes in the mechanical behavior of glass fiber/polyester composite plates [Volume 10, Issue 1, 2023, Pages 11-19]
-
Gold Nanoparticles
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Gost 4784-97 aluminum alloy
Study of the effect of instrument pin geometry on mechanical and microstructural properties of the welding region in the process of friction stir butt welding of AlMg6 [Volume 6, Issue 9, 2019, Pages 25-36]
-
Gradient temperature rolling
Effect of gradient temperature on the microstructural evolution of Nitronic 50 austenitic stainless steel thick ingot during hot rolling [Volume 10, Issue 6, 2023, Pages 65-76]
-
Grain Size
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Grain Size
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Grain Size
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Graphene Sheets
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
GRBL
Utilizing CNC technology in two-dimensional drawing and painting using a spray paint nozzle [(Articles in Press)]
-
Green synthesized
Investigating the effect of Silica/Magnesium hydroxide composite nanoparticles on the flexural properties of polymer-based nanocomposites [(Articles in Press)]
-
Grey Relational Analysis
Simulation and optimization of molding process parameters of ployetherimide parts by Taguchi-grey relational analysis combined method [Volume 10, Issue 5, 2023, Pages 19-43]
-
Grid Stiffened Composite panels
Experimental investigation of Buckling after impact strength of grid stiffened composite panels [Volume 7, Issue 11, 2020, Pages 34-41]
-
Grinding
Investigation of machining behavior of Polyether Ether Ketone in Single grit scratch test [Volume 6, Issue 9, 2019, Pages 54-62]
-
Grinding
The effect of cryogenic cooling on surface topography in the PEEK grinding process [Volume 7, Issue 1, 2020, Pages 1-12]
-
Grinding
Study and investigation of cutting energy and chip formation in the grinding process of polyether ether ketone [Volume 7, Issue 7, 2020, Pages 51-58]
-
Grinding
Investigation of the effects of wheel surface topography and coolant-lubricant types on wheel loading in grinding of Inconel 738 using image processing method [Volume 7, Issue 8, 2020, Pages 10-18]
-
Grinding burn
Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
-
GTAW welding
Effect of Temper and Quench Heat Treatment on Mechanical Properties and Microstructure of AISI 4130 to AISI 4340 Steel Joint with GTAW Process [(Articles in Press)]
-
Gurson-Tevergaard-Needleman
Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
-
Gurson-Tevergaard-Needleman
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Gypsum based composite
Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
H
-
Haptic device
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Hardfacing
The Effect of the presence of the middle layer of 309-stainless steel on microstructure and mechanical properties of St-52 carbon steel cladded by high chromium-carbon electrode produced by fusion welding [Volume 5, Issue 2, 2018, Pages 34-42]
-
Hardness
Composite fabrication and surface reinforcement of aluminum 7075 by pumice micro and nanoparticles using the friction stir process (FSP) [Volume 7, Issue 5, 2020, Pages 56-63]
-
Hardness
Fabrication and Characterization of Functionally Graded in-situ Al/Al-Cu-Cr Composite by Centrifugal Casting Process [Volume 7, Issue 9, 2020, Pages 52-64]
-
Hardness
Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
-
Hardness
Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
-
Hardness
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Hardness
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Hardness
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Hardness
Investigating the effect of the ultrasonic hammer peening on the wear properties of Aluminum alloy 6061 [(Articles in Press)]
-
Hardness
Evaluation of the effects of immersion cooling grinding (ICG) method on the surface characteristics and microstructural changes in grinding of CK45 steel [(Articles in Press)]
-
Hardness of the rubber layer
Experimental and numerical study on the distribution of thickness and dimensional accuracy of AA 6061 in two-point incremental forming using flexible die [Volume 7, Issue 11, 2020, Pages 9-20]
-
Hardness test
Experimental Study on the Effects of Harmonic Vibration on the Stress Relief of the Butt Welded AISI 1021 Pipes [Volume 7, Issue 2, 2020, Pages 1-7]
-
Hardness testing
Effect of Titanium Element on Microstructure and Mechanical Properties of Fe-Ni-C-W powder hardfacing coating [Volume 6, Issue 1, 2019, Pages 12-23]
-
Hard to cut materials
Experimental Study on surface roughness and quality of Hybrid MQL and Thermally-Enhanced Turning of Stainless Steel 17-4 PH (AISI 630) [Volume 6, Issue 8, 2019, Pages 21-32]
-
Harmonic analysis
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Heat-affected zone (HAZ)
Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
-
Heating cycle
Experiment study of tensile behavior of self-healing polymer composite under heating cycles [Volume 5, Issue 2, 2018, Pages 18-25]
-
Heating time
Experimental investigation on the effect of thickness, heating time and extrude direction on thermal shrinkage and thickness variations ABS sheet in vacuum forming process [Volume 7, Issue 8, 2020, Pages 1-9]
-
Heat Transfer Coefficient
Experimental study of anti-wear performance of nano lubricants in rotary machines gearboxes [Volume 6, Issue 2, 2019, Pages 30-38]
-
Heat treated
Investigating the microstructure and mechanical properties of vanadium bearing delta-Trip Steel [(Articles in Press)]
-
Heat treatment
Analysis of the effect of the hot stamping process on mechanical properties of 7075 aluminum alloy sheet [Volume 10, Issue 5, 2023, Pages 68-78]
-
Helical Milling
Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
-
High Chromium-Carbon Electrode
The Effect of the presence of the middle layer of 309-stainless steel on microstructure and mechanical properties of St-52 carbon steel cladded by high chromium-carbon electrode produced by fusion welding [Volume 5, Issue 2, 2018, Pages 34-42]
-
High-entropy alloys
Fabrication and characterization of FeCoNiCuCr nano structured high entropy alloy using wet mechanical alloying [Volume 9, Issue 6, 2022, Pages 1-10]
-
High frequency induction welding
Numerical and experimental investigation of the joint type effect on the heat created in weld metal in the pipe welded by high frequency induction welding [Volume 7, Issue 9, 2020, Pages 10-24]
-
High Power Diode Laser
Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
-
High Speed Rotor
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
High strength low alloy steel
Experimental determination of position effect on mechanical and metallurgical properties of HSLA multi-pass girth weld at natural gas pipelines [Volume 5, Issue 4, 2018, Pages 13-25]
-
High-temperature Tensile Testing
Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
-
HI-LOW
Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
-
Hole diameter error
The effect of drill geometrical properties on delamination and diameter error of holes in a thin sheet of Kevlar/epoxy composite [Volume 5, Issue 2, 2018, Pages 9-17]
-
Hole drilling strain gauge method
Experimental Study on the Effects of Harmonic Vibration on the Stress Relief of the Butt Welded AISI 1021 Pipes [Volume 7, Issue 2, 2020, Pages 1-7]
-
Hole drilling strain gauge method
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Hole Expansion
Investigating the microstructure, mechanical properties and hole expansion of advanced high strength steel with the approach of application in the car body [Volume 10, Issue 6, 2023, Pages 16-28]
-
Horn
Numerical Modeling of Roller Tools for Ultrasonic Welding of Thermoplastic Materials [Volume 5, Issue 2, 2018, Pages 26-33]
-
Hot and warm working
Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
-
Hot extrusion
The effect of temperature on tensile behavior and microstructure of Al-3 vol% SiC nanocomposite [Volume 5, Issue 2, 2018, Pages 1-8]
-
Hot extrusion
Fabrication of two layer Al/Cu rods using hot forward extrusion [Volume 6, Issue 4, 2019, Pages 7-13]
-
Hot extrusion
Production of aluminum-based composites from recycled chips by hot extrusion processing [(Articles in Press)]
-
Hot isostatic press
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2022, Pages 10-18]
-
Hot iso-static pressing
Rejuvenation of serviced-exposed turbine blades by application of warm hydro static pressure [Volume 4, Issue 2, 2017, Pages 39-50]
-
Hot-press joining
Experimental evaluation of joint strength in polypropylene-glass fiber reinforced composites under tensile load [Volume 6, Issue 2, 2019, Pages 39-46]
-
Hot spinning
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Hot torsion
Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
-
Hybrid composite
An experimental and numerical study on the low-velocity impact behavior of polymer matrix Kevlar-Basalt hybrid composites [Volume 7, Issue 6, 2020, Pages 44-55]
-
Hybrid fibers
Investigation the interface and charpy impact behavior of fiber metal laminates containing graphene nanoplatelets and glass kevlar hybrid fibers [Volume 6, Issue 2, 2019, Pages 10-19]
-
Hybrid friction
Analytical investigation of unbounded clad sheets by utilizing slab method and employing hybrid friction through asymmetrical rolling [Volume 6, Issue 3, 2019, Pages 51-64]
-
Hydro assisted tube pressing
Hydro assisted tube pressing as a new severe plastic deformation method for producing high strength tubes [Volume 7, Issue 5, 2020, Pages 1-13]
-
Hydrodynamic Deep Drawing
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Hydrodynamic Deep Drawing
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Hydrodynamic lubrication
Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
-
Hydroforming
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
-
Hydroforming Process
Investigation of Effect of Process Parameters on Protrusion Height of Branched Parts in Tube Hydroforming [Volume 10, Issue 1, 2023, Pages 38-48]
-
Hydrostatic tube cyclic extrusion compression process
Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
-
Hydroxy apatite
Study of the Electrochemical Corrosion Rate of Medical Implants of Titanium and Stainless Steel Made by Machining and selective laser melting under Different Surface Conditions [Volume 4, Issue 2, 2017, Pages 24-38]
-
Hydroxyapatite
Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
I
-
Identification of Boundaries
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2022, Pages 1-12]
-
Identification of chatter
The new approach to practical predicting and controlling the chatter phenomenon in the internal turning process [Volume 5, Issue 4, 2018, Pages 56-73]
-
Iinfinity structure
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Immersion cooling grinding method
Evaluation of the effects of immersion cooling grinding (ICG) method on the surface characteristics and microstructural changes in grinding of CK45 steel [(Articles in Press)]
-
Impact
Damage detection on the graphene sheet due to impact loading [Volume 9, Issue 8, 2022, Pages 26-33]
-
Impact energy
High energy absorbent Polyester/Natural Kenaf based polymer micro-composites [Volume 10, Issue 3, 2023, Pages 54-61]
-
Impact loading
Experimental and numerical investigation of the effect of metal powder particle size on the physical and mechanical properties of the components produced by high rate dynamic powder compaction [Volume 6, Issue 9, 2019, Pages 45-53]
-
Impact resistance
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Imperialist Competitive Algorithm
Simultaneous optimization of surface roughness and material removal rate in dry turning of super alloy Inconel 600 [Volume 5, Issue 3, 2018, Pages 1-11]
-
Imperialist Competitive Algorithm (ICA)
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2022, Pages 1-12]
-
Implant
Experimental study of piezoelectric properties in barium titanate implants and 3D bone scaffolds [Volume 4, Issue 2, 2017, Pages 1-9]
-
Implant
Study of the Electrochemical Corrosion Rate of Medical Implants of Titanium and Stainless Steel Made by Machining and selective laser melting under Different Surface Conditions [Volume 4, Issue 2, 2017, Pages 24-38]
-
Inclination Angle
Performance Evaluation of Self-propelled Rotary Tool in Turning [(Articles in Press)]
-
Inconel
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Inconel 600
Simultaneous optimization of surface roughness and material removal rate in dry turning of super alloy Inconel 600 [Volume 5, Issue 3, 2018, Pages 1-11]
-
Inconel 625
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Inconel-713LC
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
Inconel 738
Modeling and optimization of cutting force and surface roughness in the milling process of Inconel 738 by Neural Network and Genetic Algorithm [Volume 6, Issue 5, 2019, Pages 25-38]
-
Inconel 939 superalloy
Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
-
Inconel die
Production of Nanostructured Silver in Graphite and Inconel dies by Spark plasma sintering [Volume 7, Issue 6, 2020, Pages 1-7]
-
Increase strength
The effect of the die geometry on the joint strength of Al 3105 aluminum sheets joined by the clinching process [Volume 7, Issue 12, 2020, Pages 10-23]
-
Incremental Forming
Investigating the Effective Parameters in the Spring Back of Two Layers Sheet Copper-Austenitic Stainless Steel in the Incremental Sheet Forming [Volume 6, Issue 8, 2019, Pages 10-20]
-
Incremental Forming
Incremental forming of cylindrical aluminum flanges using a new eccentric tool [Volume 7, Issue 8, 2020, Pages 28-35]
-
Incremental Forming
The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
-
Incremental Forming
Numerical and experimental analysis of damage in the single point incremental forming of Aluminum/Copper bilayer sheet [Volume 10, Issue 1, 2023, Pages 20-29]
-
Induction heating
Experimental evaluation of deflection and angular distortion of st37 steel plates after induction line heating [Volume 5, Issue 1, 2018, Pages 37-44]
-
In-fill Density
Comparison of Tensile Strength for 3D Printed Parts Fabricated by Fused Filament Fabrication (FFF) [Volume 9, Issue 5, 2022, Pages 40-48]
-
Initial microstructure
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Injection Molding
Investigation and effect of number of recycling steps on molten flow rate and crystalline percent in injection process in wood-plastic composite [Volume 6, Issue 3, 2019, Pages 1-7]
-
Injection Molding
Controlling the warpage of plastic parts in injection molding process using the variation in coolant temperature of core and cavity [Volume 6, Issue 5, 2019, Pages 39-46]
-
Inspection
Free-form surface localization using surface partitioning and genetic algorithm [Volume 5, Issue 3, 2018, Pages 22-31]
-
Intercritical annealing
The effects of Cr addition on the phase transformation, microstructure and
mechanical properties of advanced high-strength steel [Volume 7, Issue 8, 2020, Pages 45-53]
-
Intercritical annealing
Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
-
Intermediate Canal
Experimental Investigation of the Effect of Equal Channel Angular Pressing Intermediate Canal of on the Mechanical Properties of Copper [Volume 6, Issue 1, 2019, Pages 32-41]
-
Intermetallic compounds
Experimental Investigation on Micro Friction Stir Welding of Al-Cu [Volume 9, Issue 2, 2022, Pages 18-29]
-
Internal turning
Quantitative study of forces in boring process and a new method for tool-tip force [Volume 4, Issue 2, 2017, Pages 10-23]
-
Internal Turning process
The new approach to practical predicting and controlling the chatter phenomenon in the internal turning process [Volume 5, Issue 4, 2018, Pages 56-73]
-
Internal turning tool
Dynamic modeling of an internal turning tool using experimental modal analysis and simulation of active vibration control [Volume 6, Issue 4, 2019, Pages 29-36]
-
Irradiating scheme
Experimental and numerical investigation of laser bending of tailor machined blanks with different bending mechanisms [Volume 7, Issue 11, 2020, Pages 52-65]
J
-
Jamming
Theoretical and numerical investigation of workpiece jamming in fixture using block and palm case study [Volume 6, Issue 3, 2019, Pages 20-27]
-
Jawbone Drilling
Analytical investigation of influence of rotational speed and feed rate on temperature elevation in jawbone drilling [Volume 9, Issue 1, 2022, Pages 54-62]
-
J-integral
Analysis of a Crotch corner crack in the shell-nozzle junction of a cylindrical pressure vessel under internal pressure using the J-integral method [(Articles in Press)]
-
Johnson-Cook
Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
-
Joint geometry
The effect of the die geometry on the joint strength of Al 3105 aluminum sheets joined by the clinching process [Volume 7, Issue 12, 2020, Pages 10-23]
K
-
Kenaf Fiber
High energy absorbent Polyester/Natural Kenaf based polymer micro-composites [Volume 10, Issue 3, 2023, Pages 54-61]
-
Kerf Width
Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
-
Kevlar 49
The effect of drill geometrical properties on delamination and diameter error of holes in a thin sheet of Kevlar/epoxy composite [Volume 5, Issue 2, 2018, Pages 9-17]
-
Knurling
The effect of knurling surface treatment on the strength of adhesively bonding between steel plate and carbon-phenolic composite [Volume 7, Issue 5, 2020, Pages 44-55]
L
-
Laminated composites
Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
-
Larson-Miller parameter
Rejuvenation of serviced-exposed turbine blades by application of warm hydro static pressure [Volume 4, Issue 2, 2017, Pages 39-50]
-
Laser
Design and construction of laser thickness measurement device and analysis the effect of variation of the scanning depth of field and ambient light intensity on the accuracy of point cloud [Volume 6, Issue 9, 2019, Pages 37-44]
-
Laser
Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
-
Laser bending
Experimental and numerical investigation of laser bending of tailor machined blanks with different bending mechanisms [Volume 7, Issue 11, 2020, Pages 52-65]
-
Laser bending process
Numerical investigation of deformation behavior in laser bending of sheet with curved irradiating scheme [Volume 9, Issue 2, 2022, Pages 1-7]
-
Laser Line Scanning
Three-Dimensional Geometry Profile Extraction of Deposits Using Linear Laser Scanning in the Directed Energy Deposition Additive Manufacturing Method [(Articles in Press)]
-
Laser Metal Deposition
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Laser Polishing
Investigating the influencing parameters on the surface roughness of polymer parts by Fused Deposition Modeling with respect to laser polishing [(Articles in Press)]
-
Laser profilometry
Effect of cutting tool vibration and tool wear on the surface topography of workpiece while machining Ti6Al4V Titanium alloy using laser profilometry [Volume 7, Issue 10, 2020, Pages 34-45]
-
Laser Shock Peening
Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
-
Laser spot welding
Experimental investigation of the effects of laser parameters on the strength and size of the weld nugget in laser spot welding of stainless steel sheet 316 [Volume 8, Issue 5, 2021, Pages 23-29]
-
Laser–waterjet hybrid machining
Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
-
Laser Welding
Numerical and experimental analysis of laser welding process parameters on weld bead geometry [Volume 7, Issue 3, 2020, Pages 63-71]
-
Laser Welding
Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
-
Lattice conical structure
Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
-
Lattice structure
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2022, Pages 35-44]
-
Layout design
Development of an Integer Linear Programming for Automatic Layout Design in Blanking and Piercing Progressive Dies [Volume 9, Issue 8, 2022, Pages 12-25]
-
Leakage
Experimental study on the indentation resistance of water pipelines repaired by polyester resins [Volume 6, Issue 6, 2019, Pages 1-11]
-
Length Scale Parameters
Chatter stability investigation of micro-milling dental bur at enamel and dentin layers [Volume 7, Issue 7, 2020, Pages 1-13]
-
Lift force
Effect of periodic variations of wing’s angle of attack on flapping lift force with variable wing geometry [Volume 7, Issue 8, 2020, Pages 19-27]
-
Line heating process
Experimental evaluation of deflection and angular distortion of st37 steel plates after induction line heating [Volume 5, Issue 1, 2018, Pages 37-44]
-
Localization
Free-form surface localization using surface partitioning and genetic algorithm [Volume 5, Issue 3, 2018, Pages 22-31]
-
Lock-in Method
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Lorentz force
Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
-
Lost foam casting
Experimental study of mechanical properties and morphology of parts made by lost foam casting for A356-Alloy [Volume 6, Issue 1, 2019, Pages 42-52]
-
Lost foam casting
Study on the experimental and finite element simulation of aluminum Compounds manufactured in lost foam casting process in the Aerospace Industry [Volume 6, Issue 2, 2019, Pages 47-55]
-
Low velocity impact
Experimental investigation of Buckling after impact strength of grid stiffened composite panels [Volume 7, Issue 11, 2020, Pages 34-41]
-
Low velocity impact
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Low velocity impact
Comparison of dynamic behavior of steel and aluminum materials with epoxy composite reinforced with carbon and glass fibers by FEM [Volume 10, Issue 6, 2023, Pages 40-52]
-
Low-velocity impact test
An experimental and numerical study on the low-velocity impact behavior of polymer matrix Kevlar-Basalt hybrid composites [Volume 7, Issue 6, 2020, Pages 44-55]
-
L-shaped joint
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
LTT
The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
-
LTT
Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
-
Lubricant
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
M
-
Machine Learning
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2022, Pages 35-44]
-
Machine manufacturing
Designing and manufacturing of a heavy equipment rotary table equipped with PLC control [Volume 10, Issue 3, 2023, Pages 43-53]
-
Machining chip
Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
-
Machining Forces
Analytical and Numerical Investigation of Machining Forces of Ultrasonic Assisted Milling [Volume 7, Issue 4, 2020, Pages 31-38]
-
Machining Parameters
The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
-
Magnesium"
The effect of continuous hot-dip galvanized steel coating thickness on the properties of dissimilar steel-magnesium joining using resistance spot welding [(Articles in Press)]
-
Magnetic abrasive finishing
The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
-
Magnetic field
The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
-
Magnetic field
The use of magnetic field to reduce the spring back in bending of aluminum sheet 1050 [(Articles in Press)]
-
Magnetic flux leakage method
Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
-
Magnetic permeability
Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
-
Magnetoelasticity
Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
-
Magneto-Rheological (MR) Damper
Design and Simulation of Magneto-Rheological (MR) Fluid Damper and
Experimental Study of its Effect on Tool Vibrations in Cut-off Operation [Volume 7, Issue 12, 2020, Pages 24-36]
-
Make to order environment
Determining the order of products entering the mixed-model assembly line using the exact methods [Volume 9, Issue 8, 2022, Pages 44-55]
-
Manova
Experimental investigation of the simultaneous effect of machining parameters, axial force and cutting torque on the surface roughness of the produced hole in the drilling of the 7000 series AL Alloy workpiece [Volume 7, Issue 1, 2020, Pages 26-38]
-
Manufacturing Uncertainty
Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
-
Mass method
Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
-
Matching
Design and build an active stereo scanner and validation of results from a metrological viewpoint [Volume 6, Issue 2, 2019, Pages 20-29]
-
Material and Construction method
Study of the Electrochemical Corrosion Rate of Medical Implants of Titanium and Stainless Steel Made by Machining and selective laser melting under Different Surface Conditions [Volume 4, Issue 2, 2017, Pages 24-38]
-
Material removal rate
Experimental Study of Material Removal Rate, Surface Roughness and Topography in Electrical Discharge Machining of Titanium Aluminide Intermetallic Compound [Volume 3, Issue 3, 2016, Pages 29-39]
-
Material removal rate
The Comparison of Output Characteristics in Electrical Discharge machining and Aluminum Powder Mixed EDM Processes on Titanium Aluminide Intermetallic Compound [Volume 4, Issue 1, 2017, Pages 25-37]
-
Material removal rate
Experimental study of the effect of electrical discharge machining parameters on surface roughness and Material removal rate of boron carbide ceramic [Volume 7, Issue 11, 2020, Pages 42-51]
-
Material removal rate
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Material removal rate
Experimental study of the effect of ultrasonic waves on the parameters of the electrochemical deburring process [Volume 10, Issue 2, 2023, Pages 1-6]
-
Mathematical Modeling
Mathematical and experimental modeling of plasma channel radius in alternating magnetic field assisted electric discharge machining process [Volume 9, Issue 11, 2022, Pages 54-65]
-
Maximum power consumption
Experimental investigation of the effect of ultrasonic welding parameters on the strength and weldability of GF/PA6 thermoplastic composites [Volume 10, Issue 5, 2023, Pages 44-56]
-
MAX Phase
The study of raw materials type on condition and production mechanism of nanocrystalline Zr-based MAX-phases [Volume 6, Issue 4, 2019, Pages 23-28]
-
Measurement index
Design and build an active stereo scanner and validation of results from a metrological viewpoint [Volume 6, Issue 2, 2019, Pages 20-29]
-
Mechanical Behavior of Composite
Investigating the effect of thermal preloading of glass fiber fabric on changes in the mechanical behavior of glass fiber/polyester composite plates [Volume 10, Issue 1, 2023, Pages 11-19]
-
Mechanical coupling
Design and fabrication of six axis force/torque sensor using strain gauges [Volume 9, Issue 3, 2022, Pages 1-10]
-
Mechanical properties
The effect of friction stir vibration processing on microstructure and mechanical properties of Al5052/SiC surface nano composite [Volume 6, Issue 1, 2019, Pages 1-11]
-
Mechanical properties
Experimental Investigation of the Effect of Equal Channel Angular Pressing Intermediate Canal of on the Mechanical Properties of Copper [Volume 6, Issue 1, 2019, Pages 32-41]
-
Mechanical properties
Fabrication of two layer Al/Cu rods using hot forward extrusion [Volume 6, Issue 4, 2019, Pages 7-13]
-
Mechanical properties
Experimental study of the effect of temperature on mechanical properties of aluminum sheets produced by equal channel angular rolling process [Volume 6, Issue 9, 2019, Pages 13-24]
-
Mechanical properties
Study of the effect of instrument pin geometry on mechanical and microstructural properties of the welding region in the process of friction stir butt welding of AlMg6 [Volume 6, Issue 9, 2019, Pages 25-36]
-
Mechanical properties
Investigating the effect of pin and shoulder rotational speed on the mechanical properties of friction stir processed region in Al6061 [Volume 7, Issue 3, 2020, Pages 34-41]
-
Mechanical properties
Assessment of using the floating bobbin tool for double sided friction stir welding of aluminium [Volume 7, Issue 3, 2020, Pages 52-62]
-
Mechanical properties
Microstructure and mechanical properties of AA5456/SiO2p nanocomposite fabricated by friction stir processing [Volume 7, Issue 4, 2020, Pages 39-47]
-
Mechanical properties
Hydro assisted tube pressing as a new severe plastic deformation method for producing high strength tubes [Volume 7, Issue 5, 2020, Pages 1-13]
-
Mechanical properties
Dissimilar welding of 5xxx and 7xxx aluminum alloy by self-reacting friction stir welding method [Volume 8, Issue 1, 2021, Pages 1-13]
-
Mechanical properties
Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
-
Mechanical properties
Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
-
Mechanical properties
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Mechanical properties
An experimental study on the influence of temperature and strain rate on the mechanical properties and delamination of GLARE 2/1 under bending load [Volume 10, Issue 4, 2023, Pages 37-47]
-
Mechanical properties
Identifying the mechanical properties of chromium nanobeams with artificial bee colony optimization method based on large deflection analysis with surface effects [Volume 10, Issue 4, 2023, Pages 48-61]
-
Mechanical properties
Experimental investigation of mechanical and electrical properties of semi-biodegradable polypropylene/hemp woven thermoplastic composite [Volume 10, Issue 4, 2023, Pages 62-77]
-
Mechanical properties
Effect of weight percentage of alumina on mechanical properties of nanocomposite produced by additive manufacturing method of digital light processing [Volume 10, Issue 5, 2023, Pages 57-67]
-
Mechanical properties
Optimizing the mechanical properties of PVC/NBR/Graphene nanocomposite for achieve maximum tensile strength and elongation at break [Volume 10, Issue 6, 2023, Pages 1-15]
-
Mechanical properties
Analysis of the effect of the hot stamping process on mechanical properties of 7075 aluminum alloy sheet [Volume 10, Issue 5, 2023, Pages 68-78]
-
Mechanical properties
Experimental investigation on mechanical properties affected by dissimilar friction stir spot welding of aluminum 6061-T6 alloy to copper [Volume 10, Issue 6, 2023, Pages 53-64]
-
Mechanical properties
Numerical Simulation and fabrication of copper thin wall tube by constrained ironing method [(Articles in Press)]
-
Mechanical properties
Experimental study of the effects of constrained groove pressing process on AA6061 sheet [(Articles in Press)]
-
Mechanical properties
Production of aluminum-based composites from recycled chips by hot extrusion processing [(Articles in Press)]
-
Mechanical properties
Investigation of Mechanical and Thermal Properties of Continuous Metal Wire Reinforced Samples in Fused Deposition Modeling for Shape Memory Stimulus [(Articles in Press)]
-
Mechanical Properties Recovery
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Mechanical Strength
Investigation the effect of bobbin tool geometry in friction stir welding of aluminum alloy 6061-T6 [Volume 6, Issue 4, 2019, Pages 1-6]
-
Medical nano coating
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Melt Flow Rate
Investigation and effect of number of recycling steps on molten flow rate and crystalline percent in injection process in wood-plastic composite [Volume 6, Issue 3, 2019, Pages 1-7]
-
Melting point
Experimental study of mechanical properties and morphology of parts made by lost foam casting for A356-Alloy [Volume 6, Issue 1, 2019, Pages 42-52]
-
Melt Pool
Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
-
Metal-Composite hybrid energy absorber
Experimental and numerical investigation on crushing of metal-composite hybrid energy absorber under a quasi-static loading [Volume 6, Issue 8, 2019, Pages 54-66]
-
Metal forming
Investigating the effect of flexible forming process variables on the uniformity of thickness distribution in U-Shaped Micro-channels [Volume 10, Issue 2, 2023, Pages 41-48]
-
Metal Injection Molding
Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
-
Metallic bipolar plate
Investigating the effect of flexible forming process variables on the uniformity of thickness distribution in U-Shaped Micro-channels [Volume 10, Issue 2, 2023, Pages 41-48]
-
Metallic Foam
Numerical investigation of deformation behavior of aluminum beams reinforced with aluminum foam [Volume 10, Issue 1, 2023, Pages 49-58]
-
Metallurgical Properties
Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
-
Metal Materials
Comparison of dynamic behavior of steel and aluminum materials with epoxy composite reinforced with carbon and glass fibers by FEM [Volume 10, Issue 6, 2023, Pages 40-52]
-
Metal matrix composites magnesium
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Metal-Nanocomposite Laminates
Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
-
Metal-organic framework
Synergic effect of flower-like Cu-based metal-organic framework/graphene nanostructures on electrochemical performance of supercapacitors [Volume 7, Issue 2, 2020, Pages 33-41]
-
MFL
Design and Manufacturing of the Magnetic Flux Leakage Inspection System for Detection of Pitting Corrosion in Gas Pipelines [Volume 5, Issue 2, 2018, Pages 43-49]
-
Mg/Hydroxyapatite
Effect of magnesium particle size on compressive strength of Mg/Hydroxyapatite porous bio-composite [Volume 10, Issue 2, 2023, Pages 33-40]
-
Micro bending
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Micro friction stir welding
Experimental Investigation on Micro Friction Stir Welding of Al-Cu [Volume 9, Issue 2, 2022, Pages 18-29]
-
Micro Milling
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2022, Pages 54-62]
-
Micro-Milling Dental Bur
Chatter stability investigation of micro-milling dental bur at enamel and dentin layers [Volume 7, Issue 7, 2020, Pages 1-13]
-
Micro/nano machining
An experimental and numerical study of tool geometry effect on microfracture characteristics in micro/nano machining of brittle porous structure [Volume 6, Issue 5, 2019, Pages 47-52]
-
Micro/nano scale contact models
Using Micro/Nano Scale Contact Models in 3D Manipulation of Deformation of Au Particles Under Angular Effect [Volume 7, Issue 5, 2020, Pages 33-43]
-
Microstructural changes of steel
Evaluation of the effects of immersion cooling grinding (ICG) method on the surface characteristics and microstructural changes in grinding of CK45 steel [(Articles in Press)]
-
Microstructural evolution
Effect of gradient temperature on the microstructural evolution of Nitronic 50 austenitic stainless steel thick ingot during hot rolling [Volume 10, Issue 6, 2023, Pages 65-76]
-
Microstructure
Mechanical behavior of Fe/ TiC surface layer fabricated by SMAW process [Volume 4, Issue 1, 2017, Pages 44-53]
-
Microstructure
The effect of friction stir vibration processing on microstructure and mechanical properties of Al5052/SiC surface nano composite [Volume 6, Issue 1, 2019, Pages 1-11]
-
Microstructure
Experimental Investigation of the Effect of Equal Channel Angular Pressing Intermediate Canal of on the Mechanical Properties of Copper [Volume 6, Issue 1, 2019, Pages 32-41]
-
Microstructure
Fabrication and microstructural study of TiB2-based ceramics with SiC and Si3N4 additives [Volume 6, Issue 5, 2019, Pages 13-17]
-
Microstructure
Microstructure and mechanical properties of AA5456/SiO2p nanocomposite fabricated by friction stir processing [Volume 7, Issue 4, 2020, Pages 39-47]
-
Microstructure
Effect of SiO2 and MoS2 nanoparticles on microstructure and wear resistance of electroless nanocomposite Ni-P-SiO2-MoS2 coating [Volume 7, Issue 9, 2020, Pages 65-71]
-
Microstructure
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Microstructure
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Microstructure
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Microstructure
Numerical Simulation and fabrication of copper thin wall tube by constrained ironing method [(Articles in Press)]
-
Microstructure
Experimental study of the effects of constrained groove pressing process on AA6061 sheet [(Articles in Press)]
-
Microstructure
Production of aluminum-based composites from recycled chips by hot extrusion processing [(Articles in Press)]
-
Microstructure analysis
Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
-
Microstructure design
Microstructure design of heterogeneous material using multisided patch [Volume 8, Issue 2, 2021, Pages 32-40]
-
Middle Layer of 309-Stainless Steel
The Effect of the presence of the middle layer of 309-stainless steel on microstructure and mechanical properties of St-52 carbon steel cladded by high chromium-carbon electrode produced by fusion welding [Volume 5, Issue 2, 2018, Pages 34-42]
-
Milling
Study of the performance of minimum quantity lubrication (MQL) and type of lubricant in the milling process of stainless steel EN 1.4903 [Volume 6, Issue 3, 2019, Pages 28-42]
-
Milling
Investigating the effect of sculptured surface curvatures on milling forces [Volume 6, Issue 6, 2019, Pages 34-43]
-
Milling
Analytical and Numerical Investigation of Machining Forces of Ultrasonic Assisted Milling [Volume 7, Issue 4, 2020, Pages 31-38]
-
Milling process
Investigation of tool and workpiece clamping effect on stability lobes in milling process [Volume 6, Issue 6, 2019, Pages 12-24]
-
Minimum quantity lubrication (MQL)
Study of the performance of minimum quantity lubrication (MQL) and type of lubricant in the milling process of stainless steel EN 1.4903 [Volume 6, Issue 3, 2019, Pages 28-42]
-
Minimum quantity lubrication (MQL)
Experimental Study on surface roughness and quality of Hybrid MQL and Thermally-Enhanced Turning of Stainless Steel 17-4 PH (AISI 630) [Volume 6, Issue 8, 2019, Pages 21-32]
-
Minimum quantity lubrication (MQL)
Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
-
Mix Model
Determining the order of products entering the mixed-model assembly line using the exact methods [Volume 9, Issue 8, 2022, Pages 44-55]
-
Mo40 alloy steel
Experimental study of the effects of the ultrasonic peening process on residual stress, surface hardness and hardness depth of parts cut with Wire EDM [(Articles in Press)]
-
Modal Analysis
Application of Modal Analysis in Vibration Reduction and Optimization of Stewart Robot Motion Control [Volume 7, Issue 11, 2020, Pages 1-8]
-
Model-based control
Design and implementation of a 2DOF human finger using shape memory alloys with computer-based online force control [Volume 5, Issue 4, 2018, Pages 44-55]
-
Modeling
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Modeling and Optimization
Modeling and optimization of cutting force and surface roughness in the milling process of Inconel 738 by Neural Network and Genetic Algorithm [Volume 6, Issue 5, 2019, Pages 25-38]
-
Modification of the Shear Distance
Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
-
Modified dynamic materials model
Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
-
Modulation
Development & Application of Modulated IR Thermography in Non-destructive Evaluation of Composite Materials by an edge detection filter and a morphological attribute profile [Volume 5, Issue 1, 2018, Pages 55-62]
-
Moldflow
Simulation and optimization of molding process parameters of ployetherimide parts by Taguchi-grey relational analysis combined method [Volume 10, Issue 5, 2023, Pages 19-43]
-
Molecular dynamic method
Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
-
Molecular Dynamics
Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
-
Molecular Dynamics Simulation
Damage detection on the graphene sheet due to impact loading [Volume 9, Issue 8, 2022, Pages 26-33]
-
Molecular dynamics simulations
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Monkman-Grant relationship
Rejuvenation of serviced-exposed turbine blades by application of warm hydro static pressure [Volume 4, Issue 2, 2017, Pages 39-50]
-
Monte Carlo simulation
Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
-
Morphological attributes
Development & Application of Modulated IR Thermography in Non-destructive Evaluation of Composite Materials by an edge detection filter and a morphological attribute profile [Volume 5, Issue 1, 2018, Pages 55-62]
-
Moving mass
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
MRR
Experimental evaluation of the simultaneous effect of Nanoparticle ZnO and spark peak current on MRR, surface roughness and surface micro cracks of the AISI1045، AISI 4140 و AISI D3 [Volume 7, Issue 10, 2020, Pages 46-60]
-
Multi-Curvature bending phenomenon
Experimental and numerical investigation of laser bending of tailor machined blanks with different bending mechanisms [Volume 7, Issue 11, 2020, Pages 52-65]
-
Multi objective Optimization
Simultaneous optimization of surface roughness and material removal rate in dry turning of super alloy Inconel 600 [Volume 5, Issue 3, 2018, Pages 1-11]
-
Multiple laser shock peening
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2022, Pages 45-53]
N
-
Nanoclay
Experimental investigation of flexural behavior of basalt fibers/epoxy-aluminum laminate composites containing nanoclay particles [Volume 5, Issue 1, 2018, Pages 45-54]
-
Nanoclay Particles
Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
-
Nanocomposite
The effect of temperature on tensile behavior and microstructure of Al-3 vol% SiC nanocomposite [Volume 5, Issue 2, 2018, Pages 1-8]
-
Nanocomposite
Synergic effect of flower-like Cu-based metal-organic framework/graphene nanostructures on electrochemical performance of supercapacitors [Volume 7, Issue 2, 2020, Pages 33-41]
-
Nanocomposite
Effect of SiO2 and MoS2 nanoparticles on microstructure and wear resistance of electroless nanocomposite Ni-P-SiO2-MoS2 coating [Volume 7, Issue 9, 2020, Pages 65-71]
-
Nanocomposite
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Nanocomposite
Fabrication of polyethylene glycol composite with silicon carbide scaffold for use in bone tissue engineering [Volume 10, Issue 3, 2023, Pages 9-17]
-
Nanocomposite
Effect of weight percentage of alumina on mechanical properties of nanocomposite produced by additive manufacturing method of digital light processing [Volume 10, Issue 5, 2023, Pages 57-67]
-
Nanocomposite
Optimizing the mechanical properties of PVC/NBR/Graphene nanocomposite for achieve maximum tensile strength and elongation at break [Volume 10, Issue 6, 2023, Pages 1-15]
-
Nanoferrites
Synthesis of CuNiF and CoMnF nano ferrites by sol-gel combustion method and their catalytic influence on thermal decomposition behavior of ammonium perchlorate nanoparticles [Volume 7, Issue 10, 2020, Pages 26-33]
-
Nano fluid
Experimental evaluation of the effect of the mass of ZnO, Nio, Fe3O4, Cdo nanoparticles on the damping ratio of Nano-fluid with glycerin base [Volume 7, Issue 2, 2020, Pages 8-16]
-
Nano-indentation
Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
-
Nanomachining
Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
-
NanoManipulation Process
An Examination of Environmental and Dimensional Parameters on Force and Critical Time of the Manipulation Process Using the Mechanical Theory of DMT Contact [Volume 7, Issue 9, 2020, Pages 1-9]
-
Nanoparticle-AP
Synthesis of CuNiF and CoMnF nano ferrites by sol-gel combustion method and their catalytic influence on thermal decomposition behavior of ammonium perchlorate nanoparticles [Volume 7, Issue 10, 2020, Pages 26-33]
-
Nanoparticle Geometry
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Nano-particles
Manufacturing and characterization of copper nano particles by ultrasonic-assisted electrical discharge machining [Volume 6, Issue 1, 2019, Pages 24-31]
-
Nanoparticles
Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
-
Nano polishing
The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
-
Nanostructured silver
Production of Nanostructured Silver in Graphite and Inconel dies by Spark plasma sintering [Volume 7, Issue 6, 2020, Pages 1-7]
-
Nanostructures
Fabrication and characterization of FeCoNiCuCr nano structured high entropy alloy using wet mechanical alloying [Volume 9, Issue 6, 2022, Pages 1-10]
-
Nanotechnology
Optimization of Physical-Mechanical Properties of light cure Resins for use in 3D printing by micro and nano additives for industrial applications [Volume 6, Issue 8, 2019, Pages 33-42]
-
Natural frequency
Investigation of dynamic absorber parameters to improve the vibration behavior of boring bar [Volume 9, Issue 7, 2022, Pages 1-8]
-
Navigation module
Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
-
NDT
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Negative die
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Neural Network
Simultaneous optimization of surface roughness and material removal rate in dry turning of super alloy Inconel 600 [Volume 5, Issue 3, 2018, Pages 1-11]
-
Neural Network
Modeling and optimization of cutting force and surface roughness in the milling process of Inconel 738 by Neural Network and Genetic Algorithm [Volume 6, Issue 5, 2019, Pages 25-38]
-
Neutral point
Analytical investigation of unbounded clad sheets by utilizing slab method and employing hybrid friction through asymmetrical rolling [Volume 6, Issue 3, 2019, Pages 51-64]
-
Nimonic105
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
NiTiHf shape memory alloys
Investigating Hot Deformation Behavior and Shape Memory Properties of Ni50Ti40Hf10 High Temperature Shape Memory Alloy [Volume 9, Issue 6, 2022, Pages 49-58]
-
Non-contact positioning
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Non-Destructive
Nondestructive investigating firmness of tuber agricultural products during storage using sound and compression tests [Volume 6, Issue 7, 2019, Pages 52-60]
-
Non-destructive test
Development & Application of Modulated IR Thermography in Non-destructive Evaluation of Composite Materials by an edge detection filter and a morphological attribute profile [Volume 5, Issue 1, 2018, Pages 55-62]
-
Non-destructive test
Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
-
Non-homogeneous Body
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2022, Pages 1-12]
-
Nonlinear strain path
Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
-
Nonlinear Timoshenko Beam
Chatter stability investigation of micro-milling dental bur at enamel and dentin layers [Volume 7, Issue 7, 2020, Pages 1-13]
-
Novolac Epoxy-based Vinyl Ester
Fabrication and numerical analysis of glass fiber reinforced composite air manifold under vibration loading [Volume 7, Issue 12, 2020, Pages 64-75]
-
Nozzle Layout
Arrangement of gas fuel nozzle in power plant turbines with the purpose of temperature spread control and based on gas fuel flow rate [(Articles in Press)]
-
Nugget
Optimization of welding parameters in resistance spot welding of AZ61 Mg alloy [Volume 5, Issue 3, 2018, Pages 44-51]
-
Number of Passes
Investigating the effect of the passes number and changing the tool rotation direction on the distribution of reinforcing particles in the FSP [Volume 10, Issue 2, 2023, Pages 7-13]
-
Numerical analysis
Theoretical and numerical investigation of workpiece jamming in fixture using block and palm case study [Volume 6, Issue 3, 2019, Pages 20-27]
-
Numerical analysis
Effect of periodic variations of wing’s angle of attack on flapping lift force with variable wing geometry [Volume 7, Issue 8, 2020, Pages 19-27]
-
Numerical analysis
Analysis and investigation of the characteristics of the flow and the force on the poppet including the edge of the flow deviation in the hydraulic check valve [(Articles in Press)]
-
Numerical Control
Utilizing CNC technology in two-dimensional drawing and painting using a spray paint nozzle [(Articles in Press)]
-
Numerical investigation
Numerical investigation of deformation behavior in laser bending of sheet with curved irradiating scheme [Volume 9, Issue 2, 2022, Pages 1-7]
-
Numerical Model
Numerical and experimental analysis of damage in the single point incremental forming of Aluminum/Copper bilayer sheet [Volume 10, Issue 1, 2023, Pages 20-29]
-
Numerical Solution
Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
-
Numerical Solution
Strength analysis of long edge freight wagon underframe using finite element method [Volume 10, Issue 4, 2023, Pages 27-36]
-
Numerical Study
Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
O
-
Ogive head projectile
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
One-way pulse
Effect of Electroforming Process Parameters with One-way Pulse Current and Reverse Pulse Current (PRC) on Mechanical Properties and Thickness Uniformity of Produced Copper U-shaped [Volume 7, Issue 10, 2020, Pages 61-72]
-
Optimal Machining Parameters
Investigation of material removal rate and surface quality of super clear crystal glass workpiece in the ultrasonic machining process [Volume 10, Issue 1, 2023, Pages 1-10]
-
Optimization by Box-Behnken design
Optimization of friction stir spot welding process parameters to achieve maximum failure load [Volume 5, Issue 1, 2018, Pages 13-27]
-
Optimization with Genetic Algorithm (GA)
Design of a new actuator for actuating a linear hydraulic valve and its optimization with genetic algorithm [Volume 4, Issue 1, 2017, Pages 1-9]
-
Ornithopter
Effect of periodic variations of wing’s angle of attack on flapping lift force with variable wing geometry [Volume 7, Issue 8, 2020, Pages 19-27]
-
Orthopedic
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Orthopedic plaque
Investigating the bending properties of polymeric orthopedic plaque made of different polymers by additive manufacturing method [Volume 9, Issue 9, 2022, Pages 21-25]
-
Outsole
Numerical and Experimental Investigation of Performance of Styrene Butadiene Rubber, Polyurethane, and Polyvinyl Chloride in Outsoles Fabrication [Volume 7, Issue 6, 2020, Pages 56-64]
-
Overlay
Investigating the effect of CMT (Cold Metal Transfer) process on dilution of the Stellite 6 overlay [Volume 7, Issue 1, 2020, Pages 53-59]
P
-
PCA
Fabrication and characterization of FeCoNiCuCr nano structured high entropy alloy using wet mechanical alloying [Volume 9, Issue 6, 2022, Pages 1-10]
-
PEDAR system
Numerical and Experimental Investigation of Performance of Styrene Butadiene Rubber, Polyurethane, and Polyvinyl Chloride in Outsoles Fabrication [Volume 7, Issue 6, 2020, Pages 56-64]
-
PEEK
The effect of cryogenic cooling on surface topography in the PEEK grinding process [Volume 7, Issue 1, 2020, Pages 1-12]
-
Penetration welding
The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
-
Penetration welding
Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
-
PEO
Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
-
Perforated Armor Plate
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Photosensitive Resins
Effects of adding nano silica on hardness and tensile properties of stereolithography 3d printed parts [Volume 7, Issue 10, 2020, Pages 1-11]
-
Piezoceramic
Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
-
Piezocomposite
Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
-
Piezoelectric
Experimental study of piezoelectric properties in barium titanate implants and 3D bone scaffolds [Volume 4, Issue 2, 2017, Pages 1-9]
-
Piezoelectric
Monitoring and detection of corrosion defect in the inner wall of the metal tube by non-destructive electromechanical impedance method [Volume 7, Issue 6, 2020, Pages 8-17]
-
Piezoelectric
Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
-
Pin geometry
Study of the effect of instrument pin geometry on mechanical and microstructural properties of the welding region in the process of friction stir butt welding of AlMg6 [Volume 6, Issue 9, 2019, Pages 25-36]
-
Pipe
Monitoring and detection of corrosion defect in the inner wall of the metal tube by non-destructive electromechanical impedance method [Volume 7, Issue 6, 2020, Pages 8-17]
-
Pipeline failure model
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Piston
Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
-
Piston alloy
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Piston aluminum alloy
Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
-
Pitting Corrosion
Investigation of Corrosion of Aluminum – Brass Alloy in Desalination Plant of South Pars Gas Complex [Volume 7, Issue 2, 2020, Pages 17-25]
-
PLA
Influence of infill density and printing pattern on flexural properties of 3D printed short carbon fiber PLA composite [Volume 7, Issue 9, 2020, Pages 42-51]
-
PLA
Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
-
Planar defects
Non-destructive measurement of internal defects using shear laser interferometry method [Volume 7, Issue 1, 2020, Pages 45-52]
-
Planar defects
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Plantar pressure
Numerical and Experimental Investigation of Performance of Styrene Butadiene Rubber, Polyurethane, and Polyvinyl Chloride in Outsoles Fabrication [Volume 7, Issue 6, 2020, Pages 56-64]
-
Plastic Composite
Investigation and effect of number of recycling steps on molten flow rate and crystalline percent in injection process in wood-plastic composite [Volume 6, Issue 3, 2019, Pages 1-7]
-
Plastic injection mold
Simulation and optimization of molding process parameters of ployetherimide parts by Taguchi-grey relational analysis combined method [Volume 10, Issue 5, 2023, Pages 19-43]
-
Plastic strain
Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
-
PLC
Designing and manufacturing of a heavy equipment rotary table equipped with PLC control [Volume 10, Issue 3, 2023, Pages 43-53]
-
Point cloud
Design and construction of laser thickness measurement device and analysis the effect of variation of the scanning depth of field and ambient light intensity on the accuracy of point cloud [Volume 6, Issue 9, 2019, Pages 37-44]
-
Polyester-Based nanocomposites
Investigating the effect of Silica/Magnesium hydroxide composite nanoparticles on the flexural properties of polymer-based nanocomposites [(Articles in Press)]
-
Polyester Resin
Experimental study on the indentation resistance of water pipelines repaired by polyester resins [Volume 6, Issue 6, 2019, Pages 1-11]
-
Polyether Ether Ketone
Investigation of machining behavior of Polyether Ether Ketone in Single grit scratch test [Volume 6, Issue 9, 2019, Pages 54-62]
-
Polyether Ether Ketone
Study and investigation of cutting energy and chip formation in the grinding process of polyether ether ketone [Volume 7, Issue 7, 2020, Pages 51-58]
-
Polylactic Acid
Effect of Infill Percentage and Raster Angle in Fused Deposition Modeling (FDM) Process on Shape Memory Properties of Poly (lactic acid) and Comparison with Compression Molding [Volume 7, Issue 5, 2020, Pages 14-23]
-
Polylactic Acid
Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
-
Polymeric Binder
Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
-
Polymeric nanocomposites
Effects of adding nano silica on hardness and tensile properties of stereolithography 3d printed parts [Volume 7, Issue 10, 2020, Pages 1-11]
-
Polymeric Sheet
The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
-
Poly-methyl-meta-carylate drilling
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Polyurethane
The Effect of Fabrication Method and Hard-phase Properties on the Thermo-viscoelastic Performance of Polyurethane-based Shape Memory Polymer Used in Medical Scaffolds [Volume 5, Issue 3, 2018, Pages 32-43]
-
Polyvinyl chloride
Optimizing the mechanical properties of PVC/NBR/Graphene nanocomposite for achieve maximum tensile strength and elongation at break [Volume 10, Issue 6, 2023, Pages 1-15]
-
Porous Implant
Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
-
Porous organic polymers
Synthesis and characterization of porous organic polymers based on diamine and trialdehyde for electrochemical energy storage [Volume 9, Issue 10, 2022, Pages 55-61]
-
Porous sheet
Buckling and bending analysis of functional porous plate using shear deformation theory [Volume 9, Issue 8, 2022, Pages 34-43]
-
Porous Structure
Investigating the energy absorption quality of the porous Schwarz P structure made by 3D printing method [Volume 9, Issue 11, 2022, Pages 13-20]
-
Porous Structure
Effect of magnesium particle size on compressive strength of Mg/Hydroxyapatite porous bio-composite [Volume 10, Issue 2, 2023, Pages 33-40]
-
Potato
Nondestructive investigating firmness of tuber agricultural products during storage using sound and compression tests [Volume 6, Issue 7, 2019, Pages 52-60]
-
Powder Metallurgy
The effect of temperature on tensile behavior and microstructure of Al-3 vol% SiC nanocomposite [Volume 5, Issue 2, 2018, Pages 1-8]
-
Powder Metallurgy
Investigating machining factors of recovery powder metallurgy parts, from filings and sintered by Design of experiments in conjunction with sensitivity analysis [Volume 7, Issue 7, 2020, Pages 24-37]
-
Powder mixed electrical discharge machining
The Comparison of Output Characteristics in Electrical Discharge machining and Aluminum Powder Mixed EDM Processes on Titanium Aluminide Intermetallic Compound [Volume 4, Issue 1, 2017, Pages 25-37]
-
Powder technology
The study of raw materials type on condition and production mechanism of nanocrystalline Zr-based MAX-phases [Volume 6, Issue 4, 2019, Pages 23-28]
-
Power
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Power metallurgy
Experimental investigation and ANN prediction of Al-SiC nano-composite properties produced using dynamic compaction method [Volume 7, Issue 1, 2020, Pages 13-25]
-
Predicting burst pressure
Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
-
Pressing speed
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Procast simulator
Study on the experimental and finite element simulation of aluminum Compounds manufactured in lost foam casting process in the Aerospace Industry [Volume 6, Issue 2, 2019, Pages 47-55]
-
Process planning
Process planning of cylindrical parts via by variant and generative methods and using of STEP file features [Volume 6, Issue 9, 2019, Pages 1-12]
-
Production mechanism
The study of raw materials type on condition and production mechanism of nanocrystalline Zr-based MAX-phases [Volume 6, Issue 4, 2019, Pages 23-28]
-
Progressive die
Development of an Integer Linear Programming for Automatic Layout Design in Blanking and Piercing Progressive Dies [Volume 9, Issue 8, 2022, Pages 12-25]
-
Protrusion height
Investigation of Effect of Process Parameters on Protrusion Height of Branched Parts in Tube Hydroforming [Volume 10, Issue 1, 2023, Pages 38-48]
-
Pulse Thermography
Thermography of the cooling channels using steam heating [Volume 7, Issue 1, 2020, Pages 39-44]
-
Pulse Thermography, steel plates
Applying pulse thermography technique for corrosion defect evaluation on the steel plates [Volume 7, Issue 5, 2020, Pages 24-32]
-
Pultrusion
Experimental evaluation of joint strength in polypropylene-glass fiber reinforced composites under tensile load [Volume 6, Issue 2, 2019, Pages 39-46]
-
Pumice particles
Composite fabrication and surface reinforcement of aluminum 7075 by pumice micro and nanoparticles using the friction stir process (FSP) [Volume 7, Issue 5, 2020, Pages 56-63]
-
Pump
Presenting the mathematical model of the variable flow rate axial piston pump with the displacement control valve [Volume 10, Issue 4, 2023, Pages 1-16]
-
Punch Force
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2022, Pages 1-9]
-
Punch penetration
Investigating the energy absorption of sandwich panel with aluminum core and skin under Quasi-static loading: A numerical and experimental study [(Articles in Press)]
-
Pure Copper
Fabrication of two layer Al/Cu rods using hot forward extrusion [Volume 6, Issue 4, 2019, Pages 7-13]
-
Pure Copper
Numerical and experimented study of UFG pure copper with high strength processed by Accumulative compound extrusion (ACE) [Volume 7, Issue 3, 2020, Pages 42-51]
-
Pyramidal lattice structures
Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
Q
-
Quadcopter
Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
-
Quasi-static loading
Experimental and numerical investigation on crushing of metal-composite hybrid energy absorber under a quasi-static loading [Volume 6, Issue 8, 2019, Pages 54-66]
-
Quasi- Static test
Experimental Investigation of Aluminum Foam Sandwich Panels under Quasi-static Loading [Volume 7, Issue 7, 2020, Pages 14-23]
-
Quenching-partitioning heat
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
R
-
Radial-forward-backward extrusion
The influences of radial-forward-backward extrusion on the microstructure and mechanical evolution of AM60 magnesium alloy by experimental and finite element micromechanical based cellular automaton approach [Volume 7, Issue 9, 2020, Pages 25-41]
-
Radial Pressure
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Radiation
Investigating electrical resistance and thermal analysis of hot spinning of titanium using resistance method [(Articles in Press)]
-
Railway frog
Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
-
Railway switches
Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
-
Rapid prototyping
An experimental investigation of fabricated parts by laser melting of Fe-Cu powder mixture, a type of rapid prototyping devices [Volume 5, Issue 1, 2018, Pages 1-12]
-
Rebar
Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
-
Recovery strain
Investigating Hot Deformation Behavior and Shape Memory Properties of Ni50Ti40Hf10 High Temperature Shape Memory Alloy [Volume 9, Issue 6, 2022, Pages 49-58]
-
Recrystallization
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Rectangular section
A numerical-experimental investigation on spring back in rectangular section thin wall hollows and extracting a relation to estimate twisted angle by considering strain harden behavior [Volume 4, Issue 1, 2017, Pages 38-43]
-
Recycled chips
Production of aluminum-based composites from recycled chips by hot extrusion processing [(Articles in Press)]
-
Recycling
Investigation and effect of number of recycling steps on molten flow rate and crystalline percent in injection process in wood-plastic composite [Volume 6, Issue 3, 2019, Pages 1-7]
-
Recycling
Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
-
Regenerative Chatter
Chatter stability investigation of micro-milling dental bur at enamel and dentin layers [Volume 7, Issue 7, 2020, Pages 1-13]
-
Regression Model
Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
-
Reinforcing particles
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Reinforcing particles
Investigating the effect of the passes number and changing the tool rotation direction on the distribution of reinforcing particles in the FSP [Volume 10, Issue 2, 2023, Pages 7-13]
-
Reliability
Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
-
Reliability
Failure Mode, Effects & Criticality Analysis on C.N.C lathe engine spindle system in Uncertain Condition [(Articles in Press)]
-
Repair with composite fibers
Analysis of crack behavior caused by corrosion in metal vessel repaired with composite under monotonic loading [Volume 10, Issue 3, 2023, Pages 34-42]
-
Reshaping
Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
-
Residual Stress
Optimization of welding parameters in resistance spot welding of AZ61 Mg alloy [Volume 5, Issue 3, 2018, Pages 44-51]
-
Residual Stress
Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
-
Residual Stress
Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
-
Residual Stress
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Residual Stress
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
Residual Stress
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2022, Pages 45-53]
-
Residual Stress
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2022, Pages 10-18]
-
Residual Stress
Experimental study of the effects of the ultrasonic peening process on residual stress, surface hardness and hardness depth of parts cut with Wire EDM [(Articles in Press)]
-
Residual stresses
Evaluation and measurement of the residual stresses in stainless steel pipes and investigation of the effects of wall thickness on the stresses distribution [Volume 4, Issue 2, 2017, Pages 61-68]
-
Residual stresses
Experimental Study on the Effects of Harmonic Vibration on the Stress Relief of the Butt Welded AISI 1021 Pipes [Volume 7, Issue 2, 2020, Pages 1-7]
-
Residual stresses
The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
-
Residual stresses
Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
-
Residual Stress Measurement
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Resistance spot weld
Optimization of welding parameters in resistance spot welding of AZ61 Mg alloy [Volume 5, Issue 3, 2018, Pages 44-51]
-
Resistance spot weld
Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
-
Resistance spot welding
Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process [Volume 6, Issue 1, 2019, Pages 53-60]
-
Resistance spot welding
Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
-
Resistance to wear
Composite fabrication and surface reinforcement of aluminum 7075 by pumice micro and nanoparticles using the friction stir process (FSP) [Volume 7, Issue 5, 2020, Pages 56-63]
-
Resolution
Resolution Improvement of a Capacitive-type linear Encoder with Untethered Slider [Volume 5, Issue 4, 2018, Pages 1-12]
-
Response Surface
The effect of current intensity and feed rate on surface roughness and fatigue life of work piece in wire electrical discharge turning (WEDT) process [Volume 7, Issue 8, 2020, Pages 36-44]
-
Response Surface Methodology
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Response surface methodology (RSM)
Investigating the effect of build orientation on surface roughness and build time using Fused Deposition Modelling [Volume 7, Issue 12, 2020, Pages 37-53]
-
Reverse pulse
Effect of Electroforming Process Parameters with One-way Pulse Current and Reverse Pulse Current (PRC) on Mechanical Properties and Thickness Uniformity of Produced Copper U-shaped [Volume 7, Issue 10, 2020, Pages 61-72]
-
Revolute-Prismatic joints
Design, modeling and motion simulation of robotic manipulators with time-varying structure in a fluid environment [Volume 9, Issue 2, 2022, Pages 41-51]
-
Robotic fish
Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
-
Robotic fish motion control
Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
-
Robotic Gripper
A Solenoid Actuated Gecko-like Robotic Gripper [Volume 6, Issue 3, 2019, Pages 43-50]
-
Robotic manipulators with time-varying dynamics
Design, modeling and motion simulation of robotic manipulators with time-varying structure in a fluid environment [Volume 9, Issue 2, 2022, Pages 41-51]
-
Roller Burnishing
Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
-
Roller Tool
Numerical Modeling of Roller Tools for Ultrasonic Welding of Thermoplastic Materials [Volume 5, Issue 2, 2018, Pages 26-33]
-
Roll Forming
Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
-
Rotary fatigue bending
Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
-
Rotary kiln
A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
-
Rotational Speed
Investigating the effect of pin and shoulder rotational speed on the mechanical properties of friction stir processed region in Al6061 [Volume 7, Issue 3, 2020, Pages 34-41]
-
Rotational Speed
Incremental forming of cylindrical aluminum flanges using a new eccentric tool [Volume 7, Issue 8, 2020, Pages 28-35]
-
Rotational Speed
The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
-
Rotational Speed
The Effect of Screw Arrangement and Drilling Parameters on the Fracture Fixation Strength of Femoral Neck [(Articles in Press)]
-
Roughness
Investigating the effect of fiber angle on the quality of the surface and delamination in the turning of epoxy composite reinforced with glass fiber [Volume 10, Issue 2, 2023, Pages 14-21]
-
Roughness Ratio
Experimental study of the effect of nanoparticles produced from sugarcane bagasse charcoal (nano biochar) on the anti-wear properties of lubricants used in bearing housing of centrifugal pumps in the petrochemical industry [(Articles in Press)]
-
Route sheets
Process planning of cylindrical parts via by variant and generative methods and using of STEP file features [Volume 6, Issue 9, 2019, Pages 1-12]
-
Rubber pad forming
Investigating the effect of flexible forming process variables on the uniformity of thickness distribution in U-Shaped Micro-channels [Volume 10, Issue 2, 2023, Pages 41-48]
S
-
Samples with variable cross section
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Sand Classification
Dimensional control of sand particles based on the Iranian National Standard Organization using image processing technique [Volume 5, Issue 3, 2018, Pages 52-62]
-
Sand Grains
Dimensional control of sand particles based on the Iranian National Standard Organization using image processing technique [Volume 5, Issue 3, 2018, Pages 52-62]
-
Sandwich Panel
Experimental Investigation of Aluminum Foam Sandwich Panels under Quasi-static Loading [Volume 7, Issue 7, 2020, Pages 14-23]
-
Sandwich Panel
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Sandwich Panel
Experimental study of energy absorption of sandwich panel with composite/elastomer skin [(Articles in Press)]
-
Sandwich Panel
Investigating the energy absorption of sandwich panel with aluminum core and skin under Quasi-static loading: A numerical and experimental study [(Articles in Press)]
-
Sandwich panels
Investigation of the energy absorption in three-layer Al/Polypropylene/Steel deep drawn cups [Volume 7, Issue 6, 2020, Pages 34-43]
-
Scaffold
Fabrication of polyethylene glycol composite with silicon carbide scaffold for use in bone tissue engineering [Volume 10, Issue 3, 2023, Pages 9-17]
-
Scanning Depth of Field
Design and construction of laser thickness measurement device and analysis the effect of variation of the scanning depth of field and ambient light intensity on the accuracy of point cloud [Volume 6, Issue 9, 2019, Pages 37-44]
-
Schwarz P structure
Investigating the energy absorption quality of the porous Schwarz P structure made by 3D printing method [Volume 9, Issue 11, 2022, Pages 13-20]
-
Sculptured Surface
Investigating the effect of sculptured surface curvatures on milling forces [Volume 6, Issue 6, 2019, Pages 34-43]
-
Seamless tube
Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
-
Second phase
Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
-
Second phase
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Selective Laser Melting Process (SLM)
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Selective Laser sintering
Optimized thermal gradient by changing temperature parameters for laser-assisted additive manufacturing process based on polyamide-12 powder using numerical model [Volume 5, Issue 4, 2018, Pages 26-36]
-
Self-healing
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Self-healing phenomenon
Experiment study of tensile behavior of self-healing polymer composite under heating cycles [Volume 5, Issue 2, 2018, Pages 18-25]
-
Self-propelled Rotary Tool
Performance Evaluation of Self-propelled Rotary Tool in Turning [(Articles in Press)]
-
SEM
Experimental study of the effect of temperature on mechanical properties of aluminum sheets produced by equal channel angular rolling process [Volume 6, Issue 9, 2019, Pages 13-24]
-
Semi-biodegradable composite
Experimental investigation of mechanical and electrical properties of semi-biodegradable polypropylene/hemp woven thermoplastic composite [Volume 10, Issue 4, 2023, Pages 62-77]
-
Sensitivity analysis
Investigating machining factors of recovery powder metallurgy parts, from filings and sintered by Design of experiments in conjunction with sensitivity analysis [Volume 7, Issue 7, 2020, Pages 24-37]
-
Sensitivity analysis
An Examination of Environmental and Dimensional Parameters on Force and Critical Time of the Manipulation Process Using the Mechanical Theory of DMT Contact [Volume 7, Issue 9, 2020, Pages 1-9]
-
Sensitivity analysis
Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
-
Sensitivity analysis
Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
-
Sensor
Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
-
Separation
Separation of healthy sperms using dielectrophoresis and thigmotaxis phenomena [(Articles in Press)]
-
Separation Efficiency
Design and construction of advanced sorting inorder to chromite segregation [Volume 9, Issue 3, 2022, Pages 11-17]
-
Severe plastic deformation
Texture evolution of 409 ferritic stainless steel tubes through severe plastic deformation and subsequent annealing [Volume 7, Issue 2, 2020, Pages 42-48]
-
Severe plastic deformation
Numerical and experimented study of UFG pure copper with high strength processed by Accumulative compound extrusion (ACE) [Volume 7, Issue 3, 2020, Pages 42-51]
-
Severe plastic deformation
Development of a new process for the severe plastic deformation of AA 1050 to improve the mechanical properties [Volume 7, Issue 4, 2020, Pages 19-29]
-
Severe plastic deformation
Hydro assisted tube pressing as a new severe plastic deformation method for producing high strength tubes [Volume 7, Issue 5, 2020, Pages 1-13]
-
Severe plastic deformation
Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
-
Severe plastic deformation
Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
-
Shape memory
The Effect of Fabrication Method and Hard-phase Properties on the Thermo-viscoelastic Performance of Polyurethane-based Shape Memory Polymer Used in Medical Scaffolds [Volume 5, Issue 3, 2018, Pages 32-43]
-
Shape memory
Effect of Infill Percentage and Raster Angle in Fused Deposition Modeling (FDM) Process on Shape Memory Properties of Poly (lactic acid) and Comparison with Compression Molding [Volume 7, Issue 5, 2020, Pages 14-23]
-
Shape memory alloys
Design and implementation of a 2DOF human finger using shape memory alloys with computer-based online force control [Volume 5, Issue 4, 2018, Pages 44-55]
-
Shape memory alloy stent
Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
-
Shape Recovery
The Effect of Fabrication Method and Hard-phase Properties on the Thermo-viscoelastic Performance of Polyurethane-based Shape Memory Polymer Used in Medical Scaffolds [Volume 5, Issue 3, 2018, Pages 32-43]
-
Shear Deformation Theory
Buckling and bending analysis of functional porous plate using shear deformation theory [Volume 9, Issue 8, 2022, Pages 34-43]
-
Shear Force
Development of a digital shear stress sensor based on induced phase difference, in order to prevent bedsores [(Articles in Press)]
-
Shear size
Non-destructive measurement of internal defects using shear laser interferometry method [Volume 7, Issue 1, 2020, Pages 45-52]
-
Shear strength
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Shear strength test
Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
-
Sheet hydroforming
Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
-
Sheet hydroforming
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2022, Pages 1-9]
-
Sheet induction heating
Experimental feasibility study of forming copper sheets by vacuum forming method [(Articles in Press)]
-
Sheet Metal Forming
Experimental feasibility study of forming copper sheets by vacuum forming method [(Articles in Press)]
-
Sheet Metal Forming
Simulation of the forming process and the springback of the spacer part using the finite element method [(Articles in Press)]
-
Shelf life
Nondestructive investigating firmness of tuber agricultural products during storage using sound and compression tests [Volume 6, Issue 7, 2019, Pages 52-60]
-
Short fibers
Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
-
Shrinkage
Controlling the warpage of plastic parts in injection molding process using the variation in coolant temperature of core and cavity [Volume 6, Issue 5, 2019, Pages 39-46]
-
Shrink fit
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2022, Pages 10-18]
-
Shunting effect
Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
-
Si3N4
Fabrication and microstructural study of TiB2-based ceramics with SiC and Si3N4 additives [Volume 6, Issue 5, 2019, Pages 13-17]
-
SIC
Fabrication and microstructural study of TiB2-based ceramics with SiC and Si3N4 additives [Volume 6, Issue 5, 2019, Pages 13-17]
-
SiC nano particles
The effect of friction stir vibration processing on microstructure and mechanical properties of Al5052/SiC surface nano composite [Volume 6, Issue 1, 2019, Pages 1-11]
-
Silica/Magnesium hydroxide
Investigating the effect of Silica/Magnesium hydroxide composite nanoparticles on the flexural properties of polymer-based nanocomposites [(Articles in Press)]
-
Silica Nanoparticles
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Silicon carbide
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Silicon Nitride
Study of nonconductive Si3N4 ceramic machining ability by electrical discharge machining process by assisting electrode [Volume 9, Issue 5, 2022, Pages 13-22]
-
Similar joints
Evaluation and measurement of the residual stresses in stainless steel pipes and investigation of the effects of wall thickness on the stresses distribution [Volume 4, Issue 2, 2017, Pages 61-68]
-
Simplex Optimization Method
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2022, Pages 1-12]
-
Simulation
Dynamic modeling of an internal turning tool using experimental modal analysis and simulation of active vibration control [Volume 6, Issue 4, 2019, Pages 29-36]
-
Simulation
Numerical and experimental analysis of laser welding process parameters on weld bead geometry [Volume 7, Issue 3, 2020, Pages 63-71]
-
Simulation
Studying the effects of preheat temperature on the turning process of CK45 steel [Volume 10, Issue 2, 2023, Pages 22-32]
-
Simulation
Effect of gradient temperature on the microstructural evolution of Nitronic 50 austenitic stainless steel thick ingot during hot rolling [Volume 10, Issue 6, 2023, Pages 65-76]
-
Simulation
Simulation of the forming process and the springback of the spacer part using the finite element method [(Articles in Press)]
-
Single crystal copper
Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
-
Single Grit Scratch Test
Investigation of machining behavior of Polyether Ether Ketone in Single grit scratch test [Volume 6, Issue 9, 2019, Pages 54-62]
-
Single Point Incremental Forming
Experimental investigation of formability of laser tailor welded steel blanks in single point incremental forming [Volume 6, Issue 6, 2019, Pages 25-33]
-
Sintering
Fabrication and microstructural study of TiB2-based ceramics with SiC and Si3N4 additives [Volume 6, Issue 5, 2019, Pages 13-17]
-
Sintering
Investigating machining factors of recovery powder metallurgy parts, from filings and sintered by Design of experiments in conjunction with sensitivity analysis [Volume 7, Issue 7, 2020, Pages 24-37]
-
Sintering
Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
-
SiO2 nanoparticles
Microstructure and mechanical properties of AA5456/SiO2p nanocomposite fabricated by friction stir processing [Volume 7, Issue 4, 2020, Pages 39-47]
-
Six-axis Force/Torque Sensor
Design and fabrication of six axis force/torque sensor using strain gauges [Volume 9, Issue 3, 2022, Pages 1-10]
-
Slab Method
Analytical investigation of unbounded clad sheets by utilizing slab method and employing hybrid friction through asymmetrical rolling [Volume 6, Issue 3, 2019, Pages 51-64]
-
Slitting method
Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
-
SLM
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
-
Smart Composite Structure
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
SMAW
Mechanical behavior of Fe/ TiC surface layer fabricated by SMAW process [Volume 4, Issue 1, 2017, Pages 44-53]
-
Sniper
Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
-
Sobol Method
An Examination of Environmental and Dimensional Parameters on Force and Critical Time of the Manipulation Process Using the Mechanical Theory of DMT Contact [Volume 7, Issue 9, 2020, Pages 1-9]
-
Sobol sensitivity analysis
Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
-
Solenoid
A Solenoid Actuated Gecko-like Robotic Gripper [Volume 6, Issue 3, 2019, Pages 43-50]
-
Sound test
Nondestructive investigating firmness of tuber agricultural products during storage using sound and compression tests [Volume 6, Issue 7, 2019, Pages 52-60]
-
Spark Plasma Sintering
Production of Nanostructured Silver in Graphite and Inconel dies by Spark plasma sintering [Volume 7, Issue 6, 2020, Pages 1-7]
-
Specific absorbed energy
Experimental Investigation of Aluminum Foam Sandwich Panels under Quasi-static Loading [Volume 7, Issue 7, 2020, Pages 14-23]
-
Specific energy absorption
Experimental and numerical investigation on crushing of metal-composite hybrid energy absorber under a quasi-static loading [Volume 6, Issue 8, 2019, Pages 54-66]
-
Sperm
Separation of healthy sperms using dielectrophoresis and thigmotaxis phenomena [(Articles in Press)]
-
Spindle
Failure Mode, Effects & Criticality Analysis on C.N.C lathe engine spindle system in Uncertain Condition [(Articles in Press)]
-
Spiral anode
Effect of Electroforming Process Parameters with One-way Pulse Current and Reverse Pulse Current (PRC) on Mechanical Properties and Thickness Uniformity of Produced Copper U-shaped [Volume 7, Issue 10, 2020, Pages 61-72]
-
Spot welding process"
The effect of continuous hot-dip galvanized steel coating thickness on the properties of dissimilar steel-magnesium joining using resistance spot welding [(Articles in Press)]
-
Spring-back
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Springback
The use of magnetic field to reduce the spring back in bending of aluminum sheet 1050 [(Articles in Press)]
-
Spring Back
A numerical-experimental investigation on spring back in rectangular section thin wall hollows and extracting a relation to estimate twisted angle by considering strain harden behavior [Volume 4, Issue 1, 2017, Pages 38-43]
-
Spring Back
Investigating the Effective Parameters in the Spring Back of Two Layers Sheet Copper-Austenitic Stainless Steel in the Incremental Sheet Forming [Volume 6, Issue 8, 2019, Pages 10-20]
-
Spring Back
Numerical and experimental investigation of the effect of local heating on the reduction of the spring back defect in the flexible roll forming process [Volume 9, Issue 9, 2022, Pages 35-44]
-
Spring Back
Simulation of the forming process and the springback of the spacer part using the finite element method [(Articles in Press)]
-
Square Tube
Investigating the effect of different parameters on the occurrence of collapse defect in re-shape rolling of circular pipe into a square tube [Volume 6, Issue 4, 2019, Pages 14-22]
-
St-52 Carbon Steel
The Effect of the presence of the middle layer of 309-stainless steel on microstructure and mechanical properties of St-52 carbon steel cladded by high chromium-carbon electrode produced by fusion welding [Volume 5, Issue 2, 2018, Pages 34-42]
-
Stability
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2022, Pages 21-34]
-
Stability limit diagram (SLD)
Theoretical and Experimental Study of the Chatter Vibration in Dry and Wet Machining Conditions in the Turning Process [Volume 7, Issue 3, 2020, Pages 1-21]
-
Stability lobe diagram
Investigation of tool and workpiece clamping effect on stability lobes in milling process [Volume 6, Issue 6, 2019, Pages 12-24]
-
Stacking sequence
An experimental and numerical study on the low-velocity impact behavior of polymer matrix Kevlar-Basalt hybrid composites [Volume 7, Issue 6, 2020, Pages 44-55]
-
Stainless Steel 316 L
Fractal-based analysis of the influence of current intensity on surface hardness and surface roughness of Steel workpiece in Electrical Discharge process [Volume 7, Issue 11, 2020, Pages 21-33]
-
Stainless steel EN 1.4903
Study of the performance of minimum quantity lubrication (MQL) and type of lubricant in the milling process of stainless steel EN 1.4903 [Volume 6, Issue 3, 2019, Pages 28-42]
-
Stainless Steels
Effect of gradient temperature on the microstructural evolution of Nitronic 50 austenitic stainless steel thick ingot during hot rolling [Volume 10, Issue 6, 2023, Pages 65-76]
-
Stamping Process
Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
-
Standing waves
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Static analysis
Strength analysis of long edge freight wagon underframe using finite element method [Volume 10, Issue 4, 2023, Pages 27-36]
-
Statistical-experimental analysis
Experimental study and statistical optimization of fabrication parameters affecting the flexural strength of composite grid-stiffened panels [Volume 8, Issue 11, 2021, Pages 1-15]
-
Steel
Investigation of the energy absorption in three-layer Al/Polypropylene/Steel deep drawn cups [Volume 7, Issue 6, 2020, Pages 34-43]
-
Steel Cup
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Steel plate forming
Experimental evaluation of deflection and angular distortion of st37 steel plates after induction line heating [Volume 5, Issue 1, 2018, Pages 37-44]
-
Stellite 6
Investigating the effect of CMT (Cold Metal Transfer) process on dilution of the Stellite 6 overlay [Volume 7, Issue 1, 2020, Pages 53-59]
-
Step Down
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Stereo vision
Design and build an active stereo scanner and validation of results from a metrological viewpoint [Volume 6, Issue 2, 2019, Pages 20-29]
-
Stewart Robot
Application of Modal Analysis in Vibration Reduction and Optimization of Stewart Robot Motion Control [Volume 7, Issue 11, 2020, Pages 1-8]
-
Strain Gauge
Design and fabrication of six axis force/torque sensor using strain gauges [Volume 9, Issue 3, 2022, Pages 1-10]
-
Strain Path
Numerical and experimental analysis of damage in the single point incremental forming of Aluminum/Copper bilayer sheet [Volume 10, Issue 1, 2023, Pages 20-29]
-
Strain Rate
Development of a new process for the severe plastic deformation of AA 1050 to improve the mechanical properties [Volume 7, Issue 4, 2020, Pages 19-29]
-
Strain Rate
An experimental study on the influence of temperature and strain rate on the mechanical properties and delamination of GLARE 2/1 under bending load [Volume 10, Issue 4, 2023, Pages 37-47]
-
Strain-rate sensitivity coefficient map
Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
-
Stress Intensity Factor (SIF)
Analysis of a Crotch corner crack in the shell-nozzle junction of a cylindrical pressure vessel under internal pressure using the J-integral method [(Articles in Press)]
-
Stress Recovery
The Effect of Fabrication Method and Hard-phase Properties on the Thermo-viscoelastic Performance of Polyurethane-based Shape Memory Polymer Used in Medical Scaffolds [Volume 5, Issue 3, 2018, Pages 32-43]
-
Structural properties
Investigation of the effect of die diameter on the structural properties of extruded polyethylene foams [(Articles in Press)]
-
Subsequent annealing
Texture evolution of 409 ferritic stainless steel tubes through severe plastic deformation and subsequent annealing [Volume 7, Issue 2, 2020, Pages 42-48]
-
Substrate material
Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
-
Super alloy
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Superalloy
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
-
Superalloy
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Supercapacitor
Synergic effect of flower-like Cu-based metal-organic framework/graphene nanostructures on electrochemical performance of supercapacitors [Volume 7, Issue 2, 2020, Pages 33-41]
-
Supercapacitor
Synthesis and characterization of porous organic polymers based on diamine and trialdehyde for electrochemical energy storage [Volume 9, Issue 10, 2022, Pages 55-61]
-
Surface alloying
Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
-
Surface composite
The effect of friction stir vibration processing on microstructure and mechanical properties of Al5052/SiC surface nano composite [Volume 6, Issue 1, 2019, Pages 1-11]
-
Surface condition
Study of the Electrochemical Corrosion Rate of Medical Implants of Titanium and Stainless Steel Made by Machining and selective laser melting under Different Surface Conditions [Volume 4, Issue 2, 2017, Pages 24-38]
-
Surface Curvatures
Investigating the effect of sculptured surface curvatures on milling forces [Volume 6, Issue 6, 2019, Pages 34-43]
-
Surface effects
Identifying the mechanical properties of chromium nanobeams with artificial bee colony optimization method based on large deflection analysis with surface effects [Volume 10, Issue 4, 2023, Pages 48-61]
-
Surface Hardness
Fractal-based analysis of the influence of current intensity on surface hardness and surface roughness of Steel workpiece in Electrical Discharge process [Volume 7, Issue 11, 2020, Pages 21-33]
-
Surface Hardness
Experimental study of the effects of the ultrasonic peening process on residual stress, surface hardness and hardness depth of parts cut with Wire EDM [(Articles in Press)]
-
Surface modification
Experimental investigation of flexural behavior of basalt fibers/epoxy-aluminum laminate composites containing nanoclay particles [Volume 5, Issue 1, 2018, Pages 45-54]
-
Surface modification
Optimization of Physical-Mechanical Properties of light cure Resins for use in 3D printing by micro and nano additives for industrial applications [Volume 6, Issue 8, 2019, Pages 33-42]
-
Surface modification
Effects of adding nano silica on hardness and tensile properties of stereolithography 3d printed parts [Volume 7, Issue 10, 2020, Pages 1-11]
-
Surface Partitioning
Free-form surface localization using surface partitioning and genetic algorithm [Volume 5, Issue 3, 2018, Pages 22-31]
-
Surface Quality
An experimental and numerical study of tool geometry effect on microfracture characteristics in micro/nano machining of brittle porous structure [Volume 6, Issue 5, 2019, Pages 47-52]
-
Surface Quality
Experimental and numerical investigation of the effect of die clearance on the cutting characteristics in the fine blanking of a complex part made of CK15 steel [(Articles in Press)]
-
Surface Response Methodology
Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
-
Surface roughness
Experimental Study of Material Removal Rate, Surface Roughness and Topography in Electrical Discharge Machining of Titanium Aluminide Intermetallic Compound [Volume 3, Issue 3, 2016, Pages 29-39]
-
Surface roughness
The Comparison of Output Characteristics in Electrical Discharge machining and Aluminum Powder Mixed EDM Processes on Titanium Aluminide Intermetallic Compound [Volume 4, Issue 1, 2017, Pages 25-37]
-
Surface roughness
Simultaneous optimization of surface roughness and material removal rate in dry turning of super alloy Inconel 600 [Volume 5, Issue 3, 2018, Pages 1-11]
-
Surface roughness
Modeling and optimization of cutting force and surface roughness in the milling process of Inconel 738 by Neural Network and Genetic Algorithm [Volume 6, Issue 5, 2019, Pages 25-38]
-
Surface roughness
The effect of cryogenic cooling on surface topography in the PEEK grinding process [Volume 7, Issue 1, 2020, Pages 1-12]
-
Surface roughness
Experimental investigation of the simultaneous effect of machining parameters, axial force and cutting torque on the surface roughness of the produced hole in the drilling of the 7000 series AL Alloy workpiece [Volume 7, Issue 1, 2020, Pages 26-38]
-
Surface roughness
Study on the effect of thickness of layers, temperature and speed of nozzle on circularity error and surface roughness of holes in parts produced during fused deposition modeling [Volume 7, Issue 7, 2020, Pages 38-50]
-
Surface roughness
The effect of current intensity and feed rate on surface roughness and fatigue life of work piece in wire electrical discharge turning (WEDT) process [Volume 7, Issue 8, 2020, Pages 36-44]
-
Surface roughness
Optimization of surface roughness, striation and burr formation during machining of aluminum 2024-T351 with abrasive water jet machining [Volume 7, Issue 10, 2020, Pages 12-25]
-
Surface roughness
Experimental evaluation of the simultaneous effect of Nanoparticle ZnO and spark peak current on MRR, surface roughness and surface micro cracks of the AISI1045، AISI 4140 و AISI D3 [Volume 7, Issue 10, 2020, Pages 46-60]
-
Surface roughness
Fractal-based analysis of the influence of current intensity on surface hardness and surface roughness of Steel workpiece in Electrical Discharge process [Volume 7, Issue 11, 2020, Pages 21-33]
-
Surface roughness
Experimental study of the effect of electrical discharge machining parameters on surface roughness and Material removal rate of boron carbide ceramic [Volume 7, Issue 11, 2020, Pages 42-51]
-
Surface roughness
Investigating the effect of build orientation on surface roughness and build time using Fused Deposition Modelling [Volume 7, Issue 12, 2020, Pages 37-53]
-
Surface roughness
Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
-
Surface roughness
Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
-
Surface roughness
Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
-
Surface roughness
Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
-
Surface roughness
Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
-
Surface roughness
The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
-
Surface roughness
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Surface roughness
Evaluation of the effects of immersion cooling grinding (ICG) method on the surface characteristics and microstructural changes in grinding of CK45 steel [(Articles in Press)]
-
Surface roughness
Performance Evaluation of Self-propelled Rotary Tool in Turning [(Articles in Press)]
-
Surface roughness
The use of neuro-fuzzy network coupled with meta-heuristic learning methods to predict surface roughness in the machining of aluminum alloys [(Articles in Press)]
-
Surface roughness
Investigating the influencing parameters on the surface roughness of polymer parts by Fused Deposition Modeling with respect to laser polishing [(Articles in Press)]
-
Surface smoothness
The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
-
Surface Topography
Experimental Study of Material Removal Rate, Surface Roughness and Topography in Electrical Discharge Machining of Titanium Aluminide Intermetallic Compound [Volume 3, Issue 3, 2016, Pages 29-39]
-
Surface Transformation Hardening
Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
-
Suspension in water
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Swirler
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
T
-
T6-7075Aluminum
Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
-
Taguchi
Experimental study of the plasma electrolyte cleaning using different signal shapes [Volume 8, Issue 8, 2021, Pages 1-11]
-
Taguchi method
Optimization of manufacturing process of GlassPolycarbonate thermoplastic laminates using Taguchi method [Volume 5, Issue 4, 2018, Pages 37-43]
-
Taguchi method
Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
-
Taguchi method
Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
-
Taguchi method
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Taguchi method
Simulation and optimization of molding process parameters of ployetherimide parts by Taguchi-grey relational analysis combined method [Volume 10, Issue 5, 2023, Pages 19-43]
-
Tail-actuated robots
Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
-
Tailor machined blank
Experimental and numerical investigation of laser bending of tailor machined blanks with different bending mechanisms [Volume 7, Issue 11, 2020, Pages 52-65]
-
TCC
Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process [Volume 6, Issue 1, 2019, Pages 53-60]
-
Temperature
The effect of temperature on tensile behavior and microstructure of Al-3 vol% SiC nanocomposite [Volume 5, Issue 2, 2018, Pages 1-8]
-
Temperature
Experimental study of the effect of temperature on mechanical properties of aluminum sheets produced by equal channel angular rolling process [Volume 6, Issue 9, 2019, Pages 13-24]
-
Temperature
Investigating the effect of pin and shoulder rotational speed on the mechanical properties of friction stir processed region in Al6061 [Volume 7, Issue 3, 2020, Pages 34-41]
-
Temperature
An experimental study on the influence of temperature and strain rate on the mechanical properties and delamination of GLARE 2/1 under bending load [Volume 10, Issue 4, 2023, Pages 37-47]
-
Temperature gradient
Numerical and experimental investigation of the joint type effect on the heat created in weld metal in the pipe welded by high frequency induction welding [Volume 7, Issue 9, 2020, Pages 10-24]
-
Temperature Parameters
Optimized thermal gradient by changing temperature parameters for laser-assisted additive manufacturing process based on polyamide-12 powder using numerical model [Volume 5, Issue 4, 2018, Pages 26-36]
-
Temperature Spread
Arrangement of gas fuel nozzle in power plant turbines with the purpose of temperature spread control and based on gas fuel flow rate [(Articles in Press)]
-
Tensile Behavior
Experiment study of tensile behavior of self-healing polymer composite under heating cycles [Volume 5, Issue 2, 2018, Pages 18-25]
-
Tensile load
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
Tensile-shear strength
Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
-
Tensile test
Manufacture and Comparison of Mechanical Properties of Reinforced Polypropylene Nanocomposite with Carbon Fibers and Calcium Carbonate Nanoparticles [Volume 6, Issue 5, 2019, Pages 1-12]
-
Terfenol-D
Experimental and theoretical study on effects of magnetic field and mechanical stress on structural coefficients and magnetomechanical behavior of terfenol-D [Volume 9, Issue 1, 2022, Pages 19-30]
-
Ternary intermetallic compound
Fabrication and Characterization of Functionally Graded in-situ Al/Al-Cu-Cr Composite by Centrifugal Casting Process [Volume 7, Issue 9, 2020, Pages 52-64]
-
Texture
Investigating the effect of fiber angle on the quality of the surface and delamination in the turning of epoxy composite reinforced with glass fiber [Volume 10, Issue 2, 2023, Pages 14-21]
-
Thermal cycling
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Thermal decomposition
Synthesis of CuNiF and CoMnF nano ferrites by sol-gel combustion method and their catalytic influence on thermal decomposition behavior of ammonium perchlorate nanoparticles [Volume 7, Issue 10, 2020, Pages 26-33]
-
Thermal Gradient
Optimized thermal gradient by changing temperature parameters for laser-assisted additive manufacturing process based on polyamide-12 powder using numerical model [Volume 5, Issue 4, 2018, Pages 26-36]
-
Thermal preloading
Investigating the effect of thermal preloading of glass fiber fabric on changes in the mechanical behavior of glass fiber/polyester composite plates [Volume 10, Issue 1, 2023, Pages 11-19]
-
Thermal Shrinkage
Experimental investigation on the effect of thickness, heating time and extrude direction on thermal shrinkage and thickness variations ABS sheet in vacuum forming process [Volume 7, Issue 8, 2020, Pages 1-9]
-
Thermex
Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
-
Thermoforming
Experimental feasibility study of forming copper sheets by vacuum forming method [(Articles in Press)]
-
Thermography
Development & Application of Modulated IR Thermography in Non-destructive Evaluation of Composite Materials by an edge detection filter and a morphological attribute profile [Volume 5, Issue 1, 2018, Pages 55-62]
-
Thermography
Finite element analysis of vibro-thermography nondestructive testing technique via local defect resonance [Volume 6, Issue 7, 2019, Pages 24-33]
-
Thermography
Thermography of the cooling channels using steam heating [Volume 7, Issue 1, 2020, Pages 39-44]
-
Thermoplastic composites
Experimental evaluation of joint strength in polypropylene-glass fiber reinforced composites under tensile load [Volume 6, Issue 2, 2019, Pages 39-46]
-
Thermoplastic composites
Experimental investigation of the effect of ultrasonic welding parameters on the strength and weldability of GF/PA6 thermoplastic composites [Volume 10, Issue 5, 2023, Pages 44-56]
-
Thermoplastic Materials
Numerical Modeling of Roller Tools for Ultrasonic Welding of Thermoplastic Materials [Volume 5, Issue 2, 2018, Pages 26-33]
-
Thermoplastic Materials
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Thermoplastic matrix
Optimization of manufacturing process of GlassPolycarbonate thermoplastic laminates using Taguchi method [Volume 5, Issue 4, 2018, Pages 37-43]
-
Thermoplastic polymers
Deposition of Continuous Glass Fibers on a Curved Surface by 3D Printer Based on Fused Filament Fabrication Technology [(Articles in Press)]
-
Thermosetting composites
High energy absorbent Polyester/Natural Kenaf based polymer micro-composites [Volume 10, Issue 3, 2023, Pages 54-61]
-
Thickness Distribution
The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
-
Thickness Distribution
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Thickness strain
Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
-
Thigmotaxis
Separation of healthy sperms using dielectrophoresis and thigmotaxis phenomena [(Articles in Press)]
-
Thinning
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Thinning
Investigation of Effect of Process Parameters on Protrusion Height of Branched Parts in Tube Hydroforming [Volume 10, Issue 1, 2023, Pages 38-48]
-
Thin-walled Tubes
Experimental and numerical investigation of energy absorption capability of holed thin-walled circular aluminum tubes under axial compression loading [Volume 10, Issue 6, 2023, Pages 29-39]
-
Thin Wall Structure
A numerical-experimental investigation on spring back in rectangular section thin wall hollows and extracting a relation to estimate twisted angle by considering strain harden behavior [Volume 4, Issue 1, 2017, Pages 38-43]
-
Three-Dimensional Manipulation
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Three-point Bending
Numerical investigation of deformation behavior of aluminum beams reinforced with aluminum foam [Volume 10, Issue 1, 2023, Pages 49-58]
-
Three point bending "
Experimental investigation of damage in corrugated multilayer sandwich panel under quasi-static three-point bending [(Articles in Press)]
-
Thrust force
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2022, Pages 19-31]
-
Ti60 Titanium Alloy
Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
-
Ti6Al4V Alloy
Effect of cutting tool vibration and tool wear on the surface topography of workpiece while machining Ti6Al4V Titanium alloy using laser profilometry [Volume 7, Issue 10, 2020, Pages 34-45]
-
TiB2
Fabrication and microstructural study of TiB2-based ceramics with SiC and Si3N4 additives [Volume 6, Issue 5, 2019, Pages 13-17]
-
Tilting Pad Journal Bearing (TPJB)
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Timoshenko beam
Simulation and modeling of dental bur force and vibration at enamel and dentin layers [Volume 6, Issue 8, 2019, Pages 43-53]
-
Titanium
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2022, Pages 35-44]
-
Titanium aluminide intermetallic compound
Experimental Study of Material Removal Rate, Surface Roughness and Topography in Electrical Discharge Machining of Titanium Aluminide Intermetallic Compound [Volume 3, Issue 3, 2016, Pages 29-39]
-
Titanium aluminide intermetallic compound
The Comparison of Output Characteristics in Electrical Discharge machining and Aluminum Powder Mixed EDM Processes on Titanium Aluminide Intermetallic Compound [Volume 4, Issue 1, 2017, Pages 25-37]
-
Titanium Carbide
Effect of Titanium Element on Microstructure and Mechanical Properties of Fe-Ni-C-W powder hardfacing coating [Volume 6, Issue 1, 2019, Pages 12-23]
-
Tool and workpiece clamping
Investigation of tool and workpiece clamping effect on stability lobes in milling process [Volume 6, Issue 6, 2019, Pages 12-24]
-
Tool diameter
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Tool geometry
An experimental and numerical study of tool geometry effect on microfracture characteristics in micro/nano machining of brittle porous structure [Volume 6, Issue 5, 2019, Pages 47-52]
-
Tool-tip force
Quantitative study of forces in boring process and a new method for tool-tip force [Volume 4, Issue 2, 2017, Pages 10-23]
-
Tool Vibrations
Design and Simulation of Magneto-Rheological (MR) Fluid Damper and
Experimental Study of its Effect on Tool Vibrations in Cut-off Operation [Volume 7, Issue 12, 2020, Pages 24-36]
-
Tool Wear
Effect of cutting tool vibration and tool wear on the surface topography of workpiece while machining Ti6Al4V Titanium alloy using laser profilometry [Volume 7, Issue 10, 2020, Pages 34-45]
-
Tool Wear
Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
-
Tool wear rate
The Comparison of Output Characteristics in Electrical Discharge machining and Aluminum Powder Mixed EDM Processes on Titanium Aluminide Intermetallic Compound [Volume 4, Issue 1, 2017, Pages 25-37]
-
Topography
Effect of cutting tool vibration and tool wear on the surface topography of workpiece while machining Ti6Al4V Titanium alloy using laser profilometry [Volume 7, Issue 10, 2020, Pages 34-45]
-
Topology optimization
Topology Optimization Of Structures With Thermal And Mechanical Loading [Volume 7, Issue 12, 2020, Pages 54-63]
-
TPIF process with flexible die thickness rubber layer
Experimental and numerical study on the distribution of thickness and dimensional accuracy of AA 6061 in two-point incremental forming using flexible die [Volume 7, Issue 11, 2020, Pages 9-20]
-
Transformation of austenite to martensite
Investigating the microstructure, mechanical properties and hole expansion of advanced high strength steel with the approach of application in the car body [Volume 10, Issue 6, 2023, Pages 16-28]
-
Trapezoidal channel cross-section
Simulation study of the effect of different channel and curvature angles on the effective strain and process load in the tubular channel angular pressing (TCAP) process using a trapezoidal channel cross-section [Volume 10, Issue 1, 2023, Pages 30-37]
-
Treatments (Q-P)
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
-
Triply Periodic Minimal Surface
Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
-
TRIP steel
Comparison of wear behavior of an alloy developed as TRIP steel and DP steel [Volume 7, Issue 4, 2020, Pages 48-54]
-
T-shape hydroforming
Experimental and numerical study of the hydroforming process of copper-aluminum double layered tube [Volume 10, Issue 3, 2023, Pages 18-33]
-
Tube
Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
-
Tube Hydroforming
Experimental and Numerical Study of Double Y-Shaped Hydroforming Using Analysis of Variance Method [Volume 6, Issue 7, 2019, Pages 34-41]
-
Tubular channel angular pressing
Simulation study of the effect of different channel and curvature angles on the effective strain and process load in the tubular channel angular pressing (TCAP) process using a trapezoidal channel cross-section [Volume 10, Issue 1, 2023, Pages 30-37]
-
Turbine Aero Engines
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Turbine Blade
Thermography of the cooling channels using steam heating [Volume 7, Issue 1, 2020, Pages 39-44]
-
Turbine nozzle baffle
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
-
Turning
The effect of current intensity and feed rate on surface roughness and fatigue life of work piece in wire electrical discharge turning (WEDT) process [Volume 7, Issue 8, 2020, Pages 36-44]
-
Turning
Studying the effects of preheat temperature on the turning process of CK45 steel [Volume 10, Issue 2, 2023, Pages 22-32]
-
Turning process
Theoretical and Experimental Study of the Chatter Vibration in Dry and Wet Machining Conditions in the Turning Process [Volume 7, Issue 3, 2020, Pages 1-21]
-
TWBs
Experimental investigation of formability of laser tailor welded steel blanks in single point incremental forming [Volume 6, Issue 6, 2019, Pages 25-33]
-
Twist extrusion process
Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
-
Two layer rod
Fabrication of two layer Al/Cu rods using hot forward extrusion [Volume 6, Issue 4, 2019, Pages 7-13]
-
Two layers sheet
Investigating the Effective Parameters in the Spring Back of Two Layers Sheet Copper-Austenitic Stainless Steel in the Incremental Sheet Forming [Volume 6, Issue 8, 2019, Pages 10-20]
-
Two-point incremental forming
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2022, Pages 32-42]
-
Type-IV composite tank
Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
U
-
Ultrafine and nanostructure metals
Review on accumulative roll bonding of ultrafine grained and nanostructured sheets [Volume 6, Issue 4, 2019, Pages 37-51]
-
Ultrasonic Cleaning
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Ultrasonic hammer peening
Investigating the effect of the ultrasonic hammer peening on the wear properties of Aluminum alloy 6061 [(Articles in Press)]
-
Ultrasonic machining
Investigation of material removal rate and surface quality of super clear crystal glass workpiece in the ultrasonic machining process [Volume 10, Issue 1, 2023, Pages 1-10]
-
Ultrasonic Peening Treatment
Experimental study of the effects of the ultrasonic peening process on residual stress, surface hardness and hardness depth of parts cut with Wire EDM [(Articles in Press)]
-
Ultrasonic suspension
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Ultrasonic Vibration
Manufacturing and characterization of copper nano particles by ultrasonic-assisted electrical discharge machining [Volume 6, Issue 1, 2019, Pages 24-31]
-
Ultrasonic Vibration
Analytical and Numerical Investigation of Machining Forces of Ultrasonic Assisted Milling [Volume 7, Issue 4, 2020, Pages 31-38]
-
Ultrasonic Vibration
Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
-
Ultrasonic waves
Finite element analysis of vibro-thermography nondestructive testing technique via local defect resonance [Volume 6, Issue 7, 2019, Pages 24-33]
-
Ultrasonic waves
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Ultrasonic Welding
Experimental evaluation of joint strength in polypropylene-glass fiber reinforced composites under tensile load [Volume 6, Issue 2, 2019, Pages 39-46]
-
Ultrasonic Welding
Experimental investigation of the effect of ultrasonic welding parameters on the strength and weldability of GF/PA6 thermoplastic composites [Volume 10, Issue 5, 2023, Pages 44-56]
-
Uncut fiber factor
Investigation the effective parameters on damages induced in composite sandwich structures through drilling [Volume 4, Issue 2, 2017, Pages 51-60]
-
Underframe
Strength analysis of long edge freight wagon underframe using finite element method [Volume 10, Issue 4, 2023, Pages 27-36]
-
Unilateral External Bone Fixator
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Untethered slider
Resolution Improvement of a Capacitive-type linear Encoder with Untethered Slider [Volume 5, Issue 4, 2018, Pages 1-12]
-
Urea Formaldehyde Microcapsule
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
V
-
Vacuum forming
Experimental feasibility study of forming copper sheets by vacuum forming method [(Articles in Press)]
-
Vanadium
Investigating the microstructure and mechanical properties of vanadium bearing delta-Trip Steel [(Articles in Press)]
-
Variable wing geometry
Effect of periodic variations of wing’s angle of attack on flapping lift force with variable wing geometry [Volume 7, Issue 8, 2020, Pages 19-27]
-
Variable wing's angle of attack
Effect of periodic variations of wing’s angle of attack on flapping lift force with variable wing geometry [Volume 7, Issue 8, 2020, Pages 19-27]
-
Velocity profile measurement
Design and fabrication of electromagnetic arrayed flow meter to measure velocity profiles in a rectangular channel [Volume 8, Issue 12, 2021, Pages 21-33]
-
Vibration Reduction
Application of Modal Analysis in Vibration Reduction and Optimization of Stewart Robot Motion Control [Volume 7, Issue 11, 2020, Pages 1-8]
-
Vibration stress relief
Experimental Study on the Effects of Harmonic Vibration on the Stress Relief of the Butt Welded AISI 1021 Pipes [Volume 7, Issue 2, 2020, Pages 1-7]
-
Vibration stress relief
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Vickers indentation
Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
-
Viscosity
Experimental evaluation of the effect of the mass of ZnO, Nio, Fe3O4, Cdo nanoparticles on the damping ratio of Nano-fluid with glycerin base [Volume 7, Issue 2, 2020, Pages 8-16]
-
Voice Coil Motor (VCM)
Design of a new actuator for actuating a linear hydraulic valve and its optimization with genetic algorithm [Volume 4, Issue 1, 2017, Pages 1-9]
W
-
Wall thickness
Evaluation and measurement of the residual stresses in stainless steel pipes and investigation of the effects of wall thickness on the stresses distribution [Volume 4, Issue 2, 2017, Pages 61-68]
-
Warpage
Controlling the warpage of plastic parts in injection molding process using the variation in coolant temperature of core and cavity [Volume 6, Issue 5, 2019, Pages 39-46]
-
Waterjet
Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
-
Water pipelines repair
Experimental study on the indentation resistance of water pipelines repaired by polyester resins [Volume 6, Issue 6, 2019, Pages 1-11]
-
Wear
Mechanical behavior of Fe/ TiC surface layer fabricated by SMAW process [Volume 4, Issue 1, 2017, Pages 44-53]
-
Wear
The Effect of the presence of the middle layer of 309-stainless steel on microstructure and mechanical properties of St-52 carbon steel cladded by high chromium-carbon electrode produced by fusion welding [Volume 5, Issue 2, 2018, Pages 34-42]
-
Wear
Evaluation of the effect of underwater friction stir welding on microstructure and tribological properties of copper and its alloy [Volume 6, Issue 7, 2019, Pages 42-51]
-
Wear
Comparison of wear behavior of an alloy developed as TRIP steel and DP steel [Volume 7, Issue 4, 2020, Pages 48-54]
-
Wear
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Wear Properties
Effect of friction stir processing with different pass numbers on the mechanical, tribological and corrosion properties of Al6061 [Volume 5, Issue 3, 2018, Pages 12-21]
-
Wear resistance
Effect of SiO2 and MoS2 nanoparticles on microstructure and wear resistance of electroless nanocomposite Ni-P-SiO2-MoS2 coating [Volume 7, Issue 9, 2020, Pages 65-71]
-
Wear resistance
Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
-
Wear resistance
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Wear resistance
Investigating the effect of the ultrasonic hammer peening on the wear properties of Aluminum alloy 6061 [(Articles in Press)]
-
Wear test
Experimental study of the effect of nanoparticles produced from sugarcane bagasse charcoal (nano biochar) on the anti-wear properties of lubricants used in bearing housing of centrifugal pumps in the petrochemical industry [(Articles in Press)]
-
WEDM
Vibration analysis of the wire tool in wire-cut EDM [Volume 10, Issue 4, 2023, Pages 17-26]
-
Weld bead geometry
Numerical and experimental analysis of laser welding process parameters on weld bead geometry [Volume 7, Issue 3, 2020, Pages 63-71]
-
Welding coating
Effect of Titanium Element on Microstructure and Mechanical Properties of Fe-Ni-C-W powder hardfacing coating [Volume 6, Issue 1, 2019, Pages 12-23]
-
Welding Parameters
Experimental investigation on mechanical properties affected by dissimilar friction stir spot welding of aluminum 6061-T6 alloy to copper [Volume 10, Issue 6, 2023, Pages 53-64]
-
Weld strength
Experimental investigation of the effects of laser parameters on the strength and size of the weld nugget in laser spot welding of stainless steel sheet 316 [Volume 8, Issue 5, 2021, Pages 23-29]
-
Weld Tensile Strength
Experimental study on manufacturing of bi-metal sandwiches with aluminum foam core and copper layers using friction stir welding [Volume 7, Issue 12, 2020, Pages 1-9]
-
Wire EDM
Experimental study and improving the manufacturing process of brass wire in wire-cut machining [Volume 10, Issue 5, 2023, Pages 79-91]
-
Wire electrical discharge turning
The effect of current intensity and feed rate on surface roughness and fatigue life of work piece in wire electrical discharge turning (WEDT) process [Volume 7, Issue 8, 2020, Pages 36-44]
-
Wire Electric Discharge Machining
Experimental study of the effects of the ultrasonic peening process on residual stress, surface hardness and hardness depth of parts cut with Wire EDM [(Articles in Press)]
-
Wire-tool vibration
Vibration analysis of the wire tool in wire-cut EDM [Volume 10, Issue 4, 2023, Pages 17-26]
-
Workpiece width
Vibration analysis of the wire tool in wire-cut EDM [Volume 10, Issue 4, 2023, Pages 17-26]
X
-
X-ray diffraction analysis
Investigation of Corrosion of Aluminum – Brass Alloy in Desalination Plant of South Pars Gas Complex [Volume 7, Issue 2, 2020, Pages 17-25]
-
XRD
Evaluation of the effect of underwater friction stir welding on microstructure and tribological properties of copper and its alloy [Volume 6, Issue 7, 2019, Pages 42-51]
Y
-
Y- shaped product
Experimental and Numerical Study of Double Y-Shaped Hydroforming Using Analysis of Variance Method [Volume 6, Issue 7, 2019, Pages 34-41]
Z
-
ZnO Nanoparticle
Experimental evaluation of the simultaneous effect of Nanoparticle ZnO and spark peak current on MRR, surface roughness and surface micro cracks of the AISI1045، AISI 4140 و AISI D3 [Volume 7, Issue 10, 2020, Pages 46-60]
Your query does not match with any item